Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
If the iron is left resting for more than 15 minutes, it will automatically shut-off. To begin ironing again after the timer has shut off the iron, pick it up by the handle. The green and red lights will come on. Turn temperature dial to desired setting and return iron to its upright position. When temperature setting has been reached, the red POWER ON/READY light will go out — you are ready to iron. 3 DIAGRAM 3 DIAGRAM 4 IRONING WITHOUT STEAM The iron can be used on the NO STEAM dry setting with or without water in the tank. However it is best to avoid having the tank too full of water while dry ironing. 1. Position temperature control dial to MIN, lowest setting. Diagram 3. 2. Shift the steam setting switch to the NO STEAM setting. Diagram 4. 3. Stand the iron on its heel in an upright position on an iron-safe surface and plug it in. 4. Turn the temperature control dial to the desired setting. Diagram 3. 5. When the indicator light turns off, the iron has reached the desired temperature. 6. If desired, you may still use the spray or burst buttons, as long as there is water in the tank. 7. When finished, turn temperature control dial to MIN, lowest setting, and unplug. Diagram 3. Allow to cool before cleaning or storing. NOTE: During ironing, the ready light may turn on again which indicates that the iron is heating up to maintain the proper temperature. CAUTION: If the iron has been used for a long time and is hot, DO NOT fill it with water. IRONING WITH STEAM When using as a steam iron, be sure the temperature setting on the control dial is within the STEAM range to avoid water spotting on a garment. 1. Position temperature control dial to MIN, lowest setting. Diagram 3. 2. With the unit UNPLUGGED, fill the iron with water. (See FILLING THE WATER TANK instructions.) 3. Stand the iron on its heel in an upright position on an iron-safe surface and plug it in. 4. Turn the temperature control dial to STEAM. Diagram 3. 5. Allowapproximately 2minutes fortheirontoreachthedesiredtemperature.(Theindicatorlight will turn off.) 6. Shift the steam switch to the STEAM position. Diagram 4. As soon as the iron is held horizontally, steam will flow through the vents. Placing the iron on its heel in an upright position interrupts the flow of steam. 7. When finished, turn temperature control dial to MIN, lowest setting and unplug. Diagram 3. Allow to cool before cleaning or storing. CAUTION: Avoid coming in contact with escaping steam. 4 IRONING WITH EXTRA STEAM IRONING WITH EXTRA STEAM CAUTION: Avoid coming in contact with escaping steam. USING THE SPRAY BUTTON For a mist of water to moisten dry and difficult fabrics such as linen, cotton or wool, or to handle stubborn wrinkles, press the spray button. The spray function is also handy to moisten creases accidentally ironed into the fabric. DIAGRAM 5 DIAGRAM 6 MAX FILLING THE WATER TANK 1. Unplug the iron before filling. 2. Press the steam switch in the NO STEAM position, and hold the iron upright. Diagram 4. 3. Using the enclosed measuring cup, slowly pour water into the water tank opening. Diagram 5. Afterwards, hold the iron horizontally and look through the water window to check the water level. (Slightly more than 2 cupfuls with the enclosed measuring cup fills the tank to maximum.) Diagram 6. Note: Your iron is designed to use tap water. However, if your water is very hard, it is recommended you use distilled water. DO NOT use water from home water softening systems because such water may contain minerals that may harm the iron. EMPTYING THE WATER TANK The water tank should be emptied after each use. To do so: 1. Unplug the iron from the electrical outlet. 2. While the iron is still warm, hold the iron over a sink and allow the iron to drain by tipping the point of the iron down. 3. Gently shake the iron to loosen any water drops that may be trapped. The warmth of the iron should dry out any remaining water. Note: If you empty the water tank after the iron has cooled, set the iron in an upright position on its heel, plug it in and set the temperature dial to maximum heat for 2 minutes. Then unplug the iron and let it cool before storing it. 5 SELF-CLEANING/FLUSHING SELF-CLEANING/FLUSHING 1. Position temperature control dial to MIN, lowest setting. Diagram 3. 2. Shift the steam switch to the NO STEAM position. Diagram 4. 3. Fill the iron’s water tank to its maximum fill line. Diagram 6. 4. Plug the iron in and set the temperature control dial to its highest setting or linen. Let it heat for 2 minutes. 5. Set the steam switch to the STEAM position. 6. Place a hand towel over the ironing surface. 7. Holding the iron horizontally 2 inches above the towel, depress the blast of steam button several times, remembering to pause at least 5 seconds between blasts to allow the iron to reheat. 8. Pass the iron over a damp cloth to clean the soleplate or use Faultless® Hot Iron Cleaner. 9. When finished, turn temperature control dial to MIN, lowest setting and unplug. Diagram 3....