Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Its security design ensures that only a registered Keypad Key can set the system. Using Your Home/Away Module Position the Keypad module at an entrance to the house, near the garage door, laundry room door, or front door. 1 Touch your Keypad Key to the Keypad port momentarily to make digital identification. 2 The Keypad emits one short beep to let you know the key was read. 3 The status LED turns red if the key was not accepted. 4 The status LED turns green to let you know the key was accepted. 5 Push either the Home or Away button, as is appropriate. The button will flash while the system responds. 6 When the system finishes responding, the Keypad will beep twice and the Home/Away Port will briefly remain lighted before turning off and becoming disabled. The Keypad port will blink from there on to assist you in locating it in the dark. Feature Locator DATA KE Y AWA Y HO M E ST AT US Discovery button DISCOVERY Back View Away button Home button Data and status LEDs Keypad port How It Works The Wireless Keypad can communicate with the Wireless System Controller to a distance of up to 60 feet indoors, and 200 feet outdoors. The controller then relays the Home or Away setting to the Motorola homesight™ program, arming or disarming devices. Controller DA T A KE Y AWAY HO M E ST AT U S 2 Package Contents DA T A KE Y AW AY HO M E ST AT U S Keypad (2) Tabletop Hardware 2 AA 12V Power Discovery Module Keypad Mounting Mounting Batteries Adapter Tool Keys Base Kit Installation Overview To install your Keypad module: 1 Choose an appropriate location for the Keypad module as described in Installation Hints. 2 Install batteries or plug the AC adapter into the wall and the module. 3 Register the module with your Wireless System Controller using a process called discovery. Refer to your Wireless System Controller documentation for instructions on how to discover your Wireless Keypad. 4 Touch your Keypad Key(s) to the Kepypad port and click on Settings/Key Management in the Motorola homesight™ software to see that the key has been registered. 5 Mount the module, using either the tabletop base, or by following the instructions for wall mounting. Back View Discovery Button DISCOVERY Installation Hints The Motorola Wireless Keypad module is constructed of UV-resistant ABS plastic. Please consider the following points when mounting the module: • If installing the Wireless Keypad outside, it should be shielded from the elements, such as underneath a porch roof. Do not install the module where it is subjected directly to the elements. • Typically, the module's wireless reception is good up to 60–200 feet from the Wireless System Controller depending on indoor or outdoor use and the number of obstacles. These can include metal framing, thick walls, and other wireless devices operating at 418 MHz. It is recommended that different positions be tried for optimal results. • If battery operation is preferred, pry off the back cover by lifting the cover at the bottom area where the AC power supply would be connected. Lift and slide the cover down to remove it, and install the batteries. 3 Installing Your Wireless Keypad Your module can either be mounted on a wall or sit on a horizontal surface using the included tabletop mount adapter. Wall Mount Your Wireless Keypad Warning: When mounting near a window, drilling too close to the glass could break the glass and possibly cause it to shatter. The window extends deeper into the frame than can be seen; therefore, ensure your screw is beyond the glass before drilling. 1 Using the holes on the drilling template found later in this guide, mark the position of the holes to be drilled. For drywall or other composite surfaces use a 7/32" drill bit. Drill a hole for each of the mounting screws and insert a plastic wall anchor into each hole. 1.6 mm (1/16 inch) For other solid surfaces, use a 1/16" drill bit. Drill a pilot hole for each of the maximum mounting screws. 2 Using the screws provided, secure the module to the wall. When mounting the screws to the wall, leave 1/16" (1.6 mm) space between the screw head and the wall. Using the mounting holes, slide the module down on to the screws until it is firmly seated. Wall Mount Drilling Template Mounting tools: Screwdriver, electric drill or awl. On hard surfaces, Motorola recommends that you pre-drill . inch deep pilot holes with a drill bit slightly smaller than the module mounting screws before securing the module to the surface. When mounting a module on soft surfaces like sheetrock, use an awl to punch holes in the material slightly smaller than the plastic anchors included in the hardware mounting kit. The illustration is drawn to a one-to-one scale, which means that it provides the exact dimensions required to mount the unit. Drill Holes In These Positions 3.00 in 4 Table Mount Your Wireless Keypad The module can be placed on any horizontal surface. 1 Make sure you have completed the discovery process. 2 Ensure that fresh batteries have been...