Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Belkin Dateigröße: 338.62 kb Dateiname: Unterrichtssprache:

Software Installation A STEP BY STEP GUIDE 2.1 Windows® 3.1 and Windows® 3.11 a. Insert the CursorWare™ diskette in the A: or B: drive. b. From the “Program Manager”, click on “File”. c. Then click on "Run". d. Type "A:INSTALL" (or "B:INSTALL") and then click on "OK". e. Click on the “Install” command button and follow the on-screen instructions to complete the installation. f. Once the installation is complete, reboot your computer. 2.2 Windows® 95, Windows® 98 and Windows NT® 4.0 a. Insert the CursorWare™ diskette in the A: or B: drive. b. Click on "Start" in the lower left corner of your screen. c. Then click on "Run". d. Type "A:INSTALL" (or "B:INSTALL") and then click on "OK". e. Click "Next". f. Click "Next". g. Specify if you are using a PS/2 or Serial mouse (see Section 1.2). h. Click “Next”. i. Click “Yes, I want to restart my computer”, then click “Finish”. Note: Remove the software from the disk drive before you restart your computer. Don't worry if it has already restarted before you can remove it. The computer will prompt you to remove it. 3 P73099-F8E203-US-man-qxd 3/9/00 8:15 AM Page 4 3. Troubleshooting Q: I can get into Windows® or into Safe Mode but I cannot use the mouse. A: If you have more than one driver, this could be causing your computer to boot in safe mode or not allow your mouse to work at all. If you are using a PS/2 mouse then the driver must state that it is using a PS/2 driver. If you are using a Serial mouse then the driver must state that it is using a Serial driver on COM1 or COM2. If you have a Serial Mouse and you are not sure whether you are using COM1 or COM2 then try moving the mouse to another serial port on the back of your computer, (most computers have two; if you have only one then it will more than likely be COM1). If you have more than one driver then you must remove the excess drivers. Q: If I have more than one mouse driver how do I remove the driver without the mouse control? How do I boot into normal Windows® mode? A: Use your "Windows®" Key at the bottom left hand corner of your keyboard if you have one, if not press "Alt + S" to go to the "Start" button in Windows® 98. Then use your "Up Arrow" to select "Settings", then use your "Right Arrow" to select "Control Panel" and then press "Enter". These steps have taken you to the "Control Panel" where you can gain access to your "Device Manager". The "Device Manager" shows your driver status and information and it will allow you to modify their settings. After entering the "Control Panel" use your "Up" and "Down" Arrows to select, "System" and then press "Enter". After entering "System Properties" use your "Right Arrow" to select "Device Manager". Then press "Tab" until you have 4 P73099-F8E203-US-man-qxd 3/9/00 8:15 AM Page 5 3. Troubleshooting (continued) selected "Computer" and then use the "Down Arrow" until your "Mouse" is highlighted. Then use your "Right Arrow" to expand and select your mouse driver or drivers. After you have chosen your mouse driver you can now modify it by removing the driver or changing the driver. To remove the driver you have selected, use your "Tab" key until the "Remove" tab is selected. Then press "Enter". This will remove the driver. Use your "Arrow" Key to select any other drivers and repeat the process until all but one driver remains. Even if it is the wrong driver you can use it and change it to the mouse driver you want. After removing or changing the mouse driver, use your "Tab" key until "Close" is selected and then press "Enter". Then you will have to reboot your computer. Use your "Windows®" Key at the bottom left hand corner of your keyboard if you have one, if not press "Alt + S". Then use the "Up Arrow" to select "Shut Down" and press "Enter". Use your "Arrow" Key to select "Restart" and press "Enter". Q: After installing the mouse driver and rebooting, my mouse will not work. How do I change the mouse driver without mouse control? A: Use your "Windows®" Key at the bottom left hand corner of your keyboard if you have one; if not press "Alt + S" to go to the "Start" button in Windows® 98. Then use your "Up" Arrow to select "Settings" then use your "Right" Arrow to select "Control Panel" and then press "Enter". These steps have taken you to the "Control Panel" where you can gain access to your "Device Manager". The "Device Manager" shows your driver status and information and it will allow you to modify their settings. 5 P73099-F8E203-US-man-qxd 3/9/00 8:15 AM Page 6 3. Troubleshooting (continued) After entering the "Control Panel" use the "Up" and "Down" Arrows to select "System" and then press "Enter". After entering "System Properties" use the "Right" Arrow to select "Device Manager". Then press "Tab" to bring your selection to "Computer" and then use the "Down" Arrow until your "Mouse" is highlighted. Then use your "Right" Arrow to expand and select your mouse driver or drivers. After you select the mouse driver, use your "Tab" key to select "Properties" and then ...

Herunterladen

Geben Sie zwei Ziffern: