Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Belkin Dateigröße: 144.18 kb Dateiname: a88d3eff-8a6e-489a-a947-ecf5ebb2948d.pdf Unterrichtssprache:

7. When your mouse is properly connected, you can start the software installation. 5 HARDWARE INSTALLATION Synchronizing your Mouse to your Receiver If the mouse does not automatically sync with the receiver, hold the button on the receiver down for three seconds. This will put the receiver into a non-ID (default) mode that is optimal when there is only one mouse and receiver present. You can confirm that you are in non-ID mode by checking the dim-light indicator on the receiver. If the LED on the receiver is dimly lit, you are in non-ID mode. If the light is off, try setting the non-ID mode again by holding the button down for three seconds. NOTE: If you have more than one ErgoFit Wireless Optical Mouse in the immediate area, you will have to change the receiver from non-ID to ID mode in order to eliminate interference. If you do not change to ID mode, you may experience cross talk with another wireless mouse, which will impede your mouse’s operation. Setting your Mouse to ID Mode 1. To set the mouse to ID mode, push the button on the receiver for one second only. The light on the receiver will light brightly. 2. Then sync the mouse to the receiver by pushing the sync button on the bottom of the mouse. Wait three to five seconds. The light on the receiver will go out and the mouse should now work properly. NOTE: Each time you follow these steps, the mouse will switch between channel 1 and channel 2 and randomly select a new ID. This allows multiple wireless mice to work in the same location without cross talk. If you experience cross talk with another wireless mouse, follow these steps to select a new ID. 6 SOFTWARE INSTALLATION IMPORTANT: Do not install the software until the mouse is connected to your computer. If you have not yet connected the mouse, please follow the Hardware Installation instructions. If your mouse is not functional after following the Hardware Installation instructions, please consult the Troubleshooting section for assistance. NOTE: Your mouse is functional without installing the software. However, we recommend software installation because the software allows you to program the mouse buttons for various functions, adding personalized efficiency and enjoyment to your computing experience. 1. Insert the CD into your computer. 2. The computer will automatically detect the CD and begin installing the software. 3. Follow the on-screen instructions to complete the installation. NOTE: If the computer does not automatically detect the CD, do the following: 1. Click the “Start” button and then select “Run”. 2. From the Run dialog box, enter “: Setup” and click “OK”. ( being the letter of the drive that identifies your CD-Rom drive under “My Computer”. For example, if the CD is in drive D, enter “D:\Setup”. 3. Follow the on-screen instructions. 7 USING THE WHEEL Your new mouse has a wheel that can be used in two ways: • Rotate it to use it as a scroll wheel. • Click it to use it as a scroll button. IMPORTANT: Universal scrolling must be enabled in order to use scrolling functions in applications; however, universal scrolling is not compatible with Microsoft® Office 97. Scrolling Your ErgoFit Wireless Optical Mouse’s scroll wheel can be used to navigate most applications that use a scroll bar. • To scroll with your mouse, simply rotate the wheel on your mouse forward or backward. AutoScroll AutoScroll allows you to automatically scroll through a document without having to move the mouse or mouse wheel constantly. • To AutoScroll while in a document, click the AutoScroll mouse button. An origin mark ( ) will appear at your pointer position. To initiate AutoScroll mode, move your pointer vertically, horizontally, or diagonally away from the origin mark. AutoScroll speed increases the further the pointer is moved away from the origin mark. To exit AutoScroll mode, press any mouse button or rotate the scroll wheel. 8 USING THE WHEEL Zooming In some Microsoft Office 97 applications (e.g., Microsoft Word 97), additional zooming functions are available. You can use the zooming function to “zoom in”, or magnify, a page or section of a page; or you can “zoom out” to see more of the page (page displays at a reduced magnification). • To zoom in, hold down the Ctrl key while rotating the mouse wheel forward. • To zoom out, hold down the Ctrl key while rotating the mouse wheel backward. 9 SOFTWARE FEATURES Your ErgoFit software enables a variety of exciting features and functions that will help you to increase your productivity with your new mouse. In order to control the ErgoFit Wireless Optical Mouse’s high-end features, you will need to access your Mouse Properties dialog box, either through the Control Panel, or through your ErgoFit software. To access your Mouse Properties dialog box, follow these steps: a) If your ErgoFit Wireless Optical Mouse software is installed, a small battery icon will appear in your system tray (bottom right panel on your screen, when using the Windows operatin...

Herunterladen

Geben Sie zwei Ziffern: