Never operate lantern without heat shield. ¦ Take lantern outdoors away from ignition sources. ¦ Turn fuel valve off. (Fig. 7) ¦ Remove protective cap from top of propane cylinder. Save cap for use in storing. (Fig. 8) ¦ Note: Use Coleman 16.4 oz. disposable propane cylinders. The LP-gas cylinder(s) used with lanterns must be constructed and marked in accordance with the specifications for LP-gas cylinders of the U.S. Department of Transportation or Transport Canada, CAN/CSA B339. Fig. 7 Fig. 8

• Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. Seams that will be exposed to rain, runoff, or ground level water are a must for sealing, seams on uncoated nylon or mesh panels don’t need treatment. There is no need to seal the seams in the roof or the factory taped seams. We recommend sealing both floor and fly seams and reinforcements. • Apply sealant to t

Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed. • With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Ro

CLEANING: • Clean the tent by setting it up and wiping it down with a mild soap (liquid hand soap) and lukewarm water solution. Rinse thoroughly and dry completely. Never use detergent, washing machines or dryers because they can damage the tent’s protective coating and seams. After cleaning, be sure the tent is completely dry, especially the heavier, double-stitched areas such as the seams, before storing or mold / mildew are likely to grow. • Clean the tent poles with a cloth and lubricate the

Pull the tent into a rough hexagon. Do not stake down the tent just yet; but in windy conditions, stake down one corner that faces into the wind. 2 Assemble the shockcorded tent poles and rod. Carefully seat each section. Try to keep the poles from snapping together as this can damage the ends. Set the shorter vestibule rod aside. 3 Insert the tent poles into the mesh sleeves. • Near the side of the door, insert and slide a pole through the continuous mesh sleeve from A to B. Push the pole rathe

(Press the RECOVERY button again to return the main display.) TEMPERATURE: Screen will display room temperature in sleep mode. ScoreConditionHeartRate(fromtestHRminusendHR) F1ExcellentAbove50F2Good40~49F3Average30~39F4Fair20~29F5Poor10~19F6VeryPoorUnder10 Console Information GENERAL INFORMATION: 1. Start pedaling or press any button to start Console. 2. The console will shut down after 4 minutes of no activity, and will display room temperature. Begin pedaling or press any button to bring consol

• Never use inside house, camper, tent, vehicle or other unventilated or enclosed areas. This lantern consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. CAUTION • SERVICE SAFETY • Use only propane set up for vapor withdrawal. • Keep all connections and fittings clean. Inspect propane cylinder and lantern propane connections for damage before attaching. • During set up, CHECK FOR LEAKS in one or more ways: Apply soapy water to connections. Look for

.. Screw propane cylinder into lantern. Take care not to cross-thread. Hand tighten only. (Fig. 9) Fig. 9 Fig. 2 Globe Ventilator Bail Upper Carrying Case AAA Battery .. Assemble bail as shown with handle toward back of the lantern. (Fig. 4) Fig. 4 Fig. 5 Fig. 6 Upper Carry Case Collar Fig. 1 .. Install upper carry case. Align the unlock symbol “ “ on the collar with the unlock symbol on the upper carry case. Rotate the upper carry case until the lock symbol “ “ on the collar aligns with the loc

Do not bounce tent bag on its end to get the tent out. These actions may cut the shock cord and/or damage the pole ends. 1. Unroll and unfold the tent and lay it on the ground. In windy conditions, stake down one front corner into wind. See fig.1. 3. Fit the posts into the grommets: There are webs and grommets sewn to each corner of the tent. Start at either end and insert the locking posts from the base of the frame poles into one of the grommets. Repeat at the opposite end, raising the frame a

Start at one end and drag the fly up and over the top of the tent [works best with two people]. It only fits one way; align the yellow web of the fly to the yellow web on the tent. See fig.8. • Reach under the fly and wrap all the Velcro® straps around the poles to secure the fly to the frame. See fig. 9. Stake down the y: • There are, web/ring assemblies on the bottom at each side of the fly vestibule door. Pull these out and away from the tent and to stake down. Adjust as necessary. See fig.10