Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
- Clam Customer Service Information Model No. - 8060 - p/n 108306 Specifications ..Height: 60” (21” packed) ..Width: 35 inches ..Depth: 81” (35” packed) ..Weight: 45 lbs. - Clam Customer Service Information NOTICE!! Once used, this shelter cannot be returned to the store. If you have a Warranty Claim, please contact Clam Corporation Customer Service by email inquiry or direct by calling: . . Clam Corporation, Inc. 600 Clydesdale Trail Medina, MN 55340 . Phone - 763-231-4120 . Fax - 763-231-4121 . Website – . Email – Customer Service Hrs: - 8am to 4pm, Mon. - Fri. Central Standard Time Clam Corporation, Inc. Manual – 102178 - Step One -- Step One - 2 - Step Two - - Step Two - 3 - Step Three - Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the ends. - Step Three - Slide the Canopy Hoop Poles onto the Canopy Poles until the spring buttons engage the holes near the ends. - Step Four - Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles, attaching the Roof Velcro as you go. Feed the length of the Porch Hoop Pole through the Porch Hoop Sleeve sewn on the Tent. Slide the Porch Hoop Pole onto the Porch Poles, engaging the second hole position. Attach the Porch Velcro on each side of the Tent. The Tent is now ready to be “set” in the next step. - Step Four - Drape the Tent over the supported hoops then go inside and spread out the Canopy Hoop Poles, attaching the Roof Velcro as you go. Feed the length of the Porch Hoop Pole through the Porch Hoop Sleeve sewn on the Tent. Slide the Porch Hoop Pole onto the Porch Poles, engaging the second hole position. Attach the Porch Velcro on each side of the Tent. The Tent is now ready to be “set” in the next step. 5 - Step Five - To “set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly installed, the Porch Hoop Pole will lightly touch the floor. To achieve this condition, start by finding the center of the Molding. From behind the unit, pull the midpoint of the Tent downward and fold the Tent material under the lip of the Base. Then press the midpoint of the molding over the Tent material and Base lip. Continue pressing outward in both directions until you have secured about twelve inches of material to the base Having temporarily secured the tent to the base, take a walk around the unit. Readjust the Molding until you have verified the proper Porch Hoop Pole position and also that the Tent sides and corners are properly proportioned. When satisfied, continue applying the Molding around the shelter, one direction from center and then the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. Secure the Molding with the included #6 Phillips Screws. Evenly space them about every ten to twelve inches, and also put a screw in the center of both corners. Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation. - Step Five - To “set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel Molding is correctly installed, the Porch Hoop Pole will lightly touch the floor. To achieve this condition, start by finding the center of the Molding. From behind the unit, pull the midpoint of the Tent downward and fold the Tent material under the lip of the Base. Then press the midpoint of the molding over the Tent material and Base lip. Continue pressing outward in both directions until you have secured about twelve inches of material to the base Having temporarily secured the tent to the base, take a walk around the unit. Readjust the Molding until you have verified the proper Porch Hoop Pole position and also that the Tent sides and corners are properly proportioned. When satisfied, continue applying the Molding around the shelter, one direction from center and then the other, pulling the material as you go so that surface is relatively wrinkle-free and snug. Secure the Molding with the included #6 Phillips Screws. Evenly space them about every ten to twelve inches, and also put a screw in the center of both corners. Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation. 6 -T i p s f o r U s e --T i p s f o r U s e - Folding and transporting your Fish Trap is easy: ..Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. ..Cover with the Travel Cover* (an optional but recommended accessory to help prolong the life of the unit). Tow the unit out to your favorite fishin...