Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Website – . Email – customerservice@clamcorp.com Fri. Central Standard Time Clam Corporation cannot honor warranty without an original, dated receipt. -P art s Li st --P art s Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 101080 SCREW, 1/4-20 X 1.25 8 101081 WASHER, 1/4 FLAT 16 101082 NUT, 1/4-20 THIN NYLOCK 26 101083 TUBE SPACER CAP 8 101088 SCREW, 1/4-20 X 0.75 14 101140 SCOUT PORCH HOOP 1 101043 LH CANOPY BRACKET 1 101609 SEAT RAIL SUPPORT BRACKET 2 101042 RH CANOPY BRACKET 1 101141 SCOUT CANOPY HOOP 3 102494 BASE, SCOUT 08-09 1 101095 TOW ROPE, 3/8 DIA X 9 FT 1 101096 U-CHANNEL MOLDING, SCOUT 1 101148 SCREW, #6 X 0.38 16 101055 STADIUM SEAT 1 101486 SCREW, 1/4-20 X 1.75 4 101144 ACCESSORY HAMMOCK, SCOUT 1 101429 PLUG, 1.16 DIA TUBE 4 101097 SCREW, #14 X 1.00 4 101607 SCOUT SEAT RAIL TUBE 2 101147 SCREW, #10 x 1.00 4 101048 SLIDE BLOCK 4 101146 ALUMINUM CHANNEL 2 102432 TENT, 08/09 SCOUT 1 102475 MANUAL, 08/09 SCOUT 1 2 -P art s Di ag r a m --P art s Di ag r a m - 3 -St e p O n e --St e p O n e - 4 -St e p Tw o --St e p Tw o - 5 -St e p T hr e e - Scout Base (p/n 102494) -St e p T hr e e - Scout Base (p/n 102494) -St ep F o u r --St ep F o u r - 7 -St ep Fi v e --St ep Fi v e - 8 -St e p S i x --St e p S i x - 9 -St e p S e ve n --St e p S e ve n - 10 -St e p Ei ght - Scout Tent (p/n 102432) -St e p Ei ght - Scout Tent (p/n 102432) 11 -St ep N i n e --St ep N i n e - 12 -St e p T en --St e p T en - If everything still looks good, secure the Molding with the #6 Phillips Screws. Evenly space them about every ten to twelve inches, and also put a screw in the center of both corners. Since there aren’t any predrilled holes, it's advisable to use a powered driver for this operation. 13 -Set -u p & T a k e Do w n --Set -u p & T a k e Do w n - Set-Up -Rotate the hoop poles forward, then position and expand the adjustable spreader pole in the rear of the unit to take the slack out of the tent. Tighten the tension knob on the rear adjustable spreader pole to hold its position. Take-Down -Go around the shelter and tuck the tent material in between the rested hoops to keep the tent from spilling out of the base and contacting the ground. Also make sure that the tent is clear of the canopy brackets edges and other items in the base which might cause rubbing and premature wear to the tent. If you purchased the optional travel cover, cover your shelter to protect your gear from the elements during transport. -S a f et y I nst r u ct i o ns - PLEASE FULLY UNDERSTAND AND FOLLOW ALL SAFETY INSTRUCTIONS AS OUTLINED. FAILURE TO DO SO COULD RESULT IN SEVERE INJURY OR DEATH. . Do not use open flame heaters in your ice shelter. Injury or death may result from fire if tent fabric is exposed to open flame. The tent is not fireproof, but the fabric is treated with a fire retardant that meets CPAI-84 specifications. Application of any foreign substance may render the flame retardant properties ineffective. Ice Armor fabric will melt when contact is made with hot surfaces (i.e., heaters). . Death from asphyxiation may result from use of oxygen depleting heaters. Open all vents for fresh air ventilation. . Never leave shelter unattended when set up. . Due to the increase in traffic (snowmobiles, autos, etc.) on area lakes, ice fishing can be hazardous at night. Ifyou chooseto fish at night or inpoorvisibilityconditions,besuretotakeprecautionswith lights or reflectors to show drivers your whereabouts. Exterior reflectors must be visible at all times to reduce risk of collisions. -W ar r a nt y - Clam Corporation warrants to the original retail purchaser that all Clams are free from manufacturer’ s defects for one (1) year from the date of original purchase. Warranty does not cover cracked windows, tent tears, broken or bent hoops due to high wind weather conditions or unattended use. Clam Corporation will replace or repair any part found defective within the one (1) year time limit. All parts must be returned to Clam Corporation. Before returning any parts, you must first call or write and acquire a return authorization. All returns must be returned postage-prepaid and include the original cash register receipt (date and purchase price). Note: Please write the return authorization number on the outside of the package to help ensure the transaction gets processed swiftly and accurately. -Li m it at i o n of L i a bi lit y - It is expressly understood that Clam Corporation’s liability for its products, whether due to breach of warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam Corporation is not liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to use, or the repair or replacement of Clam Corporation products. Clam Corporation reserves the right to make alterations or modificat...