Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Bowflex Dateigröße: 4.06 mb Dateiname: Unterrichtssprache:

Machine Mat The Bowflex® TreadClimber® Machine Mat is an optional accessory for the TreadClimber® machine that helps keep your workout area free from debris and dust. The rubber machine floor mat provides a non-slip surface when mounting and dismounting the TreadClimber® machine, limits static discharge when you touch the machine, and greatly reduces the possibility of display or running errors. A rubberized mat will protect your flooring when you are performing repairs or maintenance. Put your Bowflex® TreadClimber® Machine Mat in your selected workout area before beginning assembly to protect your floors and your TreadClimber® machine from damage. Assembly Manual 4 Assembly Manual Parts Box 1 contains: Qty: 1 Descr: Control Panel/Handlebar Assembly Qty: 2 Descr: Left and Right Side Foot Support Platform Qty: 1 Descr: Right Side Plastic Frame Cover Qty: 1 Descr: Left Side Plastic Frame Cover Qty: 1 Descr: Left Side Plastic Drive Cover Qty: 1 Descr: Right Side Plastic Drive Cover Qty: 2 Descr: Left & Right Hydraulic Cylinder Qty: 1 Descr: Left Upright Support Qty: 1 Descr: Rear Cover Qty: 2 Descr: Plastic Upright Junction Covers Qty: 1 Descr: Right Upright Support Assembly Manual 5 Box 1 also contains: Qty:1 Owner’s Manual Bag Contains the following: • The Bowflex® TreadClimber® Assembly Guide and Owner’s Manual • (1) Drive Belt • Power Cord • (2) Treadle Decals • (2) Drive Cover Decals • TreadClimber® Safety Key *Note: TC1000 Safety Key plugged into console for shipping. • Heart Rate Monitor Chest Strap (TC5000 Only) • (1) #2 Phillips Screw Driver Qty:1 Assembly Hardware Bag Contains the following: • (1) #2 Phillips Screwdriver • (2) 5/16" x 1 1/2" Button Head Screw • (1) 3/16" Hex Key • (12) 5/16" Flat Washers SAE (smaller O.D.) • (1) 5/32" Hex Key • ( 2) 5/16" Acorn Nut • (1) 9/16" Open End Wrench • (6) 1/4" x 1" Flat Head Screw • (2) 5/16" Flat Washers • ( 4) 3/8" Cosmetic Plugs • (14) 5/16" x 1" Button Head Screw • (16) #10 Phillips Note: Occasionally extra parts are included. Parts Box 2 contains the TreadClimber® treadles Box 3 contains the TreadClimber® base Qty: 1 Descr: TreadClimber® Treadle Assembly Qty: 1 Descr: TreadClimber® Base Cylinder Stud Hardware Qty: 6 Descr: 1/4” x 1” Flat Head Screw Qty: 2 Descr: 5/16” x 1 1/2” Button Head Screw Qty: 16 Descr: #10 Phillips Head Screw Qty: 14 Descr: 5/16” x 1” Button Head Screw Qty: 2 Descr: 5/16” Flat Washer Qty: 12 Descr: 5/16” Flat Washer SAE Qty: 4 Descr: 3/8” Cosmetic Plugs Qty: 2 Descr: 5/16” Acorn Nut Hardware: Tools: Qty: 1 Qty: 1 Descr: #2 Phillips Screwdriver Descr: 3/16” Hex Key Qty: 1 Qty: 1 Descr: 9/16” Open End Wrench Descr: 5/32” Hex Key Parts: Qty: 1 Qty: 1 Descr: Drive Belt Descr: Safety Key with Clip (Models TC3000 & TC5000 only.) Assembly Manual AssemblStep 1: Put the Treadles on the Base Parts: • TreadClimber® Base Assembly • TreadClimber® Treadle Assembly Hardware: • (4)3/8”X11/4”HexBolts(preassembled) Note: Hardware is only hand tightened. Finish tightening the hardware in Step 1-5 below. Tools: • 9/16”OpenEndWrench(included) • Scissorsorothercuttingtool• RulerNote: This step requires two people. 1-1 Unlock the latch lever (see Figure 1-1). 1-2 With assistance, lower the tower treadle assembly onto base. 1-3 Align roller casting flush to the base (See Figure 1-2) 1-4 Use a ruler to center the treadles between the upright bases. 1-5 Tighten the (4) 3/8” x 1 1/4” Hex Bolts on the rear roller casting and base with the 9/16” open end wrench (See Figure 1-3). Note: Tighten the outside bolts on the rear roller casting first, then the inner bolts. 1-6 Cutthetreadleziptielocatedunderneaththetreadles. Roller casting aligned to lie flush onbase Figure 1-2 Figure 1-3 Assembly 8 Assembly Manual Assembly Figure 2-1 Step 2: Connect the Speed Sensor Wires Parts: • TreadClimber® Base and Treadle assembly from Step 1 2-1 Find the wires labeled ‘Speed Sensor Wire’ and connect them (see Figure 2-1). The Speed Sensor is located directly above the Speed Sensor Wire. Step 3: Connect the Step Sensor Wires Parts: • TreadClimber® Base and Treadle assembly from Step 2 Note: The TC1000 is not equipped with the step sensor function. Tuck the unused step sensor wire through the hole in frame and continue to the next step. 3-1 Connect the Step Sensor Wires (See Figure 3-1). Push any excess wire through holes in frame (See Figure 3-2). Figure 3-1 Speed Wire Figure 3-2 Assembly Step 4: Lock the Treadles Parts: • TreadClimber® Base and Treadle assembly from Step 3 4-1 Line up the treadles parallel to each other. 4-2 Move the locking lever down and to the left and then up into the locked position until it clicks (See Figure 4-1). 4-3 From the front of the machine, press down on each treadle individually until they lock into the down position. The treadles might unlock during workout if they are not fully engaged. Figure 4-1 Lever in locked position Step 5: Attach the Drive Belt Parts: • TreadClimber® Base and Treadle assembly from Step 4 • (1) Drive Belt Tools: • 3...

Herunterladen

Geben Sie zwei Ziffern: