Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Pay special attention to orientation terms such as: door, 12 o'clock, yellow marked pole, interior/exterior, WARNING label. Page 7 Top view ASSEMBLY STEPS Read through all assembly steps carefully before beginning to assemble the tent. Refer to drawings for clarification. It is recommended that two people assemble this tent together. A 9/16" socket and ratchet, or box-end wrench are required for assembly. Wear gloves while you assemble the tent. The trampoline will be used as an assembly “table” to keep the tent off the ground and to provide a frame of reference. Remove any ladders or anything on the trampoline that will hinder assembling the tent on the trampoline mat (bed) or frame. Step 1: First verify that you have received all the tent parts. Use the shipping container to keep all the hardware together. You should have the following pieces: (see page 15 for details). If you do not have the required parts then contact your dealer or JumpKing before proceeding (see page 14). 2 - pole attachment bracket assemblies. 2 - sliding - pole attachment pieces. 2 - long poles. 1 - short pole. 1 - tent with attached tie string pouch. 1 - tent floor. 1 - stuff sack Step 2: Make sure the frame pad is installed and secured properly to the trampoline top frame. First place the circular tent floor on the trampoline mat (bed). Attach the plastic hooks to the end of the springs where they attach to the "v" ring on the mat. Attach one hook and then stretch the floor and attach the next hook to the closest spring - continue this process evenly around the circumference of the mat. The tent floor must cover the mat (bed) smoothly and evenly (see Fig. 1). Step 3: Assemble the three poles by joining the sections together. These are slip joints. Do not force these joints together. The internal shock cord holds the poles somewhat rigidly together (see Fig. 2). Be careful of the pole ends as they are a potential hazard (over head power lines, eyes) and are not easily controlled due to the pole length and flexibility. After assembly they should be placed on the ground. After assembling the poles you should have two (2) long poles and one (1) shorter pole. The short pole is the middle support pole. One pole will have a yellow sticker on each end. This is the 12 o'clock pole. Plastic hook to spring end at "v" ring. FIGURE 1 Shock cord Insert Pole sections FIGURE 2 Page 8 Step 4: Step 4: Place the tent on the mat (bed) and determine where you want the door of the tent to be located. The door is "D" shaped and has zippers on the outside. A WARNING label should be on the outside next to the door. This will be your tent access point. Now attach a tent pole support bracket assembly (see page Fig. 3 for assembly details - make sure the curved part of the front piece is up against the top frame) to a vertical leg that is at 90 degrees to the door (3 o'clock -see Fig 3). To attach the bracket will require tools. Tighten the bolts/nuts securely. A lock washer should be placed between the back piece and the securing nut. The bracket should be as close to the top frame as possible. The rotating pole dowels to which the tent poles will finally attach should be outside the frame (see Fig. 4). At 9 o'clock attach the second bracket to a vertical leg (see Fig. 3). Both assemblies should be aligned parallel and "snug" to the top frame. Step 5: Now arrange the tent on the mat (bed) of the trampoline so that interior side of the tent is UP and the pole sleeves are accessible. A WARNING label is on the exterior of the tent near the door. Locate the tent pole sleeves on the interior (side up) of the tent through which the poles will be inserted. Insert the short pole into the middle sleeve. Do not force the pole(s) through the sleeve(s). You will have to gather tent fabric together to ease the poles through the sleeves. Put the long pole with the yellow stickers on the ends in the sleeve away from the door this sleeve has yellow fabric at each end - this is the 12 o'clock pole. The other long pole goes into the sleeve at the door 6 o'clock. Leave the pole ends exposed outside the tent fabric edge (see Fig.5). These poles are longer than the width of the trampoline and will be bowed to erect the tent. Now gather the tent together and turn the whole assembly over and rotate it so the door is back where you want it (6 o'clock) and all of the pole ends are close to the pole attachment brackets. Be careful to not tear the tent fabric on the springs. At the 12 o'clock position - opposite the door loosely attach a velcro strap that is part of the tent bottom to the top frame. The strap should go over the top of the frame pad and wrap around the top tubular frame part. This strap will be at the mid-point of the window. This is to hold the tent down at that point until the poles are finally attached to the brackets and the tent is erected. 12 o'clock Bracket (9 o'clock) Bracket (3 o'clock) D Door (6 o'clock) Top of frame rotating pole dowels Outside of frame FIG...
Dieses Handbuch ist für folgende Modelle:Camping - JKTR12T2 (116.82 kb)