Stimmen - 4, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
These actions may cut the shock cord and/or damage the pole ends. 1. Unpack the tent bag and separate the components. Unfold the tent and lay it out with the floor on the ground and with a grommeted web in each corner. Pull the tent into a rough rectangle. Do not stake down the tent just yet; but in windy conditions, stake down one corner that faces into the wind. 2. Assemble the three shockcorded tent poles. Carefully seat each section. Try to keep the poles from snapping together as this can damage the rod ends. 3. At the front of the tent body at A, slide a pole diagonally across the tent, through the sleeves, to the opposite side B. Follow the seam from sleeve to sleeve. Push the pole, don't pull it. Continue with the second pole through its sleeves from C to D. Finish with the third pole from E to F. See fig.1. 4. Insert the post end of a pole into its grommet on the corner stake-out web. See fig.2. At the opposite corner, grasp the web and simultaneously push the pole to form an arc. Insert the post into the grommet to maintain tension. See fig.3.Repeat with the remaining poles, raising the tent. See fig.4. 5. Your tent is now free-standing; place it in the desired location and use the metal skewers to stake it down. 6. With the tent secure, unroll the fly and drape it over the tent. The fly only fits one way; make sure the vestibule panel window is directly over the front door of the tent. Reach under the fly and connect the Velcro® fasteners to the tent poles, through the openings in the sleeves. See figs.5 & 6. 7. Connect the six side-release buckles on the fly to their mates on the tent webs. See fig.7. 8. At the rear of the tent, stake down the pull-out web on the fly. 9. At the front of the tent, pull the vestibule taut and stake it down. Make sure that the vestibule is tight across the door flap. With the vestibule staked down and tight, go to the corners / sides of the tent and adjust the web pull-outs to tighten. Then if necessary, adjust the rear vestibule stake out loop. See Fig.8. Your tent is now ready for use. NOTE: • The vestibule door of the fly can be rolled up at the bottom, up to the top or to the side for better ventilation. Attach the toggle to hold in place. To help prevent condensation, keep the doors open. • In strong winds, tie extra ropes to the storm loops on the fly and stake down. • Take down : Pull up stakes. Release the fly's Velcro® and buckles. Remove fly and open door. Pull posts out of the grommets and push poles out of the sleeves. Collapse the tent poles and stow. Fold the tent onto itself and fold the fly and lay it on tent. Roll up both towards the door and stow. REV.C 4.09 Fig.1 Fig.2 Fig.3 Fig4 Fig.5 Fig.6 Fig.7 Fig.8 Good: 4 stakes /4 lines Best: 4 stakes /8 lines REV E. FEB 09 SEAM SEALING: We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor SeamGrip®. • Work in a fully ventilated area. • Set the tent up or lay the tent out flat. Taut seams allow for even application and penetration of the sealer. • Decide which seams need to be sealed. For example, seams that will be exposed to rain, runoff, or ground level water are a must for sealing, while seams on uncoated nylon or mesh panels don’t need treatment. There is no need to seal the seams in the roof or the factory taped seams. We recommend sealing both floor and fly seams and reinforcements. • Apply sealant to the inside and outside of all exposed seams. Several thin layers will work better than one thick layer. Read and follow manufacture's instructions. STAKING: All tents need to be staked down to keep them from blowing away. Securing the tent by placing heavy objects inside is just not adequate. • Once the tent body is erected, stake it out before the fly is put on. This enables you to square the tent up to ensure that the fly goes on properly and that the seams align with the frame. Pull the base of the tent taut between each web stake out loop or ring & pin. Make sure that all corners are square. It is important that you don’t stake the tent out too tightly. You will know it’s too tight, if the door zippers can not be easily operated. Drive stakes through the web loops, or with ring & pin, drive the stake just outside the ring so that the “J” hook catches it. Tie a piece of cord or web into a loop through the ring to be used as a large stake loop if needed. • With the tent properly staked, drape the fly over the frame, attach its tent connection points and stake down any pull outs. • Do not attempt to remove the stakes by pulling on the tent becket loop, as this could cause the fabric to tear. The best way is to pry on the stake itself. Staking in special conditions: • Sand. Use long, broad stakes with plenty of surface area in loose soil. • Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes separately. Their sharp edges can cut fabric and leave rust stains, which might damage your tent. • Snow. Use “dead man” anchors. Tie tent to buried objects (branches, ten...
Dieses Handbuch ist für folgende Modelle:Camping - Assault Outfitter 4 (4.64 mb)