Stimmen - 0, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Pole Descriptions Pole Pole Pole Description Qty. Dia. Repair Kit Replacement Kit Leg Pole, metal 4 19mm N/A 5010000650 Leg Pole, metal, with white marking 2 19mm N/A 5010000651 Top Pole, thick, grey, 1 12.7mm 5010000538 5010000550 Top Pole, thick, black 2 12.7mm 5010000538 5010000550 Door Pole, long, thin, black, fiberglass, rubber tips 1 6.3mm 5010000543 5010000545 Vert. Door Pole, short, black, fiberglass, rubber tips 1 6.3mm 5010000543 5010000545 To Set Up Tent 1. Unfold tent and spread out on a clean, level surface with the door facing the desired direction. (Fig. 1) 2. Assemble all fiberglass and metal poles by interlocking the shock-corded, sections together. 3. Insert thick, black, Top Poles through the sleeves on top of tent forming an X”; then push end of each pole into black Pole Connector to form an arch. (Fig. 1 & 1A) 4. Insert thick, grey Top Pole through the grey trimmed center sleeve, running from the front to the back of tent; then push end of pole into black Pole Connector to form an arch. (Fig. 1 & 1B) 5. Insert four metal Leg Poles into end of Pole Connectors at the four corners of the tent. (Fig. 1 & 1C) NOTE: Make sure end with metal “V” spring is inserted into Pole Connector. 6. Insert two metal Leg Poles (with white markings) into end of Pole Connectors at front & back of the tent. (Fig. 1 & 1C) NOTE: Make sure end with metal “C” spring is inserted into Pole Connector. Fig. 1 Door & Front of Tent Metal Leg Pole Metal Leg Pole with White Marking Pole Connector Metal Leg Pole with White Marking Metal Leg Poles Pole Connector Metal Leg Pole 1C “C” Spring“C” Spring 1A 1B 7. Rotate metal Leg Poles to upright position; then insert metal pin on web strap at front, back, & four corners of tent into bottom of each pole. (Fig. 2 & 2A) NOTE: You can use the tri-glide to adjust the length of the center webbing to make it easier to insert the metal pin into the metal center pole. 8. Snap large frame clips on seams of tent onto metal Leg Poles to secure. (Fig. 2 & 2B) 9. Stretch four corners of tent until taut; then drive metal stake through ring on web strap of each to secure (Fig. 2 & 2C). 10. Stretch web strap at front & back of tent until taut; then drive metal stake through ring on each to secure (Fig. 2 & 2C). 2A 2B Fig. 2 2C Tri-Glide Hinged, Rigid Door 1. Insert Vertical Door Pole (shorter black pole with plastic cap tips) through zippered vertical sleeve on hinged side of door. (Fig. 3) 2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge (Fig. 4). Zip up vertical pole sleeve. 3. Insert Door Pole (long, black pole with plastic cap tips) into zippered pole sleeve at top of door. (Fig. 5) 4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 6) 5. Zip up “C” shaped pole sleeve to enclose Door Pole. (Fig. 7) Fig. 3 Fig. 4 Pole Sleeve Fig. 5 Pole Sleeve Fig. 7 Fig. 6 To Attach Rainfly 1. Drape Rainfly over tent with the triangle-shaped leg flaps with elastic cords centered over the four corner of the tent. (See Fig. 8 on other side of this tag). NOTE: Hook and loop fasteners, located on seams of under side of rainfly, should be centered over the Leg Poles. (continued on other side) To Attach Rainfly (continued) Fig. 8 Rainfly Front of Tent Door Triangle-shaped Leg Cover 2. Locate all hook & loop fasteners on underside of Rainfly and Leg Covers; then wrap around four corner and front and back Leg Poles to secure. (Fig. 9, 9A, & 9B) 3. Stretch elastic straps and hook clip on each to the metal loops at the four corners of the tent at the bottom of the Leg Poles. (Fig. 9 & 9C) 4. Stretch elastic straps above center front and back leg; then hook onto metal ring on Leg Pole. (Fig. 9 & 9D) 5. Stretch all guylines until taut, then secure with stakes. (Fig. 9 & 9E) 9C Fig. 9 Door 9A 9B 9D 9E Electrical Cord Access 1. Unzip access panel in the lower left front corner of tent and bring in electrical cord. Use only UL approved cords that are rated for outdoor usage. (Fig. 10) Fig. 10 Cooler Access The smaller zippered opening at the back of tent is designed for added ventilation and easy access to your beverage cooler. 1. To use as a cooler access, unzip other flap to make an avenue to bring beverages into tent. (Fig. 11) 2. To use as a vent, unzip flap to expose screen. Fig. 11 Attaching Room Divider & Overhead Storage Panel 1. Divider Panel can be installed through center of the tent by inserting the toggles through top and bottom fabric loops as shown. (Fig. 12 & 12A) 2. Install the Overhead Storage Panel by inserting the toggles through the fabric loops at the top of the tent. Fig. 12 Zippered Divider Panel Overhead Storage Panel 12A Top Fabric Loops To Store 1. All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case. 2. Make sure tent is clean and dry before placing i...