Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
– Do not set up your tent under trees. – For best results in windy conditions, (2) Rainfly Poles position the end of tent into the wind. Hinged Door Pole Vertical Hinged Door Pole Rainfly Part No. 9278-1091 1 Layout & Positioning of Tent, Pole Assembly – Layout and position tent with door facing desired direction. (illus. 1) – Unzip door. – Stake down tent corners, using the tent stake loops. Keep the floor taut. (illus. 2) – Assemble all poles by interlocking shock- corded poles. – Insert the black poles into center pole sleeves marked with black binding. The poles should cross forming an “X” in the middle of tent. (illus. 1) Black poles illus. 2 Tent stake through stake loop Front door illus. 1 POLE ASSEMBLY PARTS Part No. 9278B3681 Part No. 9278B3691 Part No. 9278B3651 Part No. 9278-1101 Part No. 9278-1111 2 2 Connect Frame to Tent – Locate the pin & ring systems on either side of the front door and the corresponding pin & rings on the back side of tent. – Insert one end of black frame pole onto pin & ring system on tent stake loop on either side of front door. (illus. 3) – Go to opposite end of pole diagonally from starting point and gradually apply pressure to the pole forming an arch until you are able to insert the pin into pole end. – Repeat for second pole. – Attach tent frame clips to poles. illus. 3 pin & ring system located on the front & rear of tent illus. 4 Center section upright Black poles illus. 8 Completed tent with rainfly. illus. 7 Insert rainfly pole through pole sleeve on underside of rainfly. End guylines Stake down doormat Light illus. 11 Charger End guylines Stake down doormat Light illus. 11 Charger 3 Raise Ends of Tent – Insert grey shorter shock-corded poles through pole sleeves marked with grey binding at both ends of tent above windows. – Insert second pin (located near center of tent) of pin & ring system into pole end. – Go to opposite end of pole and gradually apply pressure to the pole forming an arch until you are able to insert the pin into the pole end. – Attach frame clips. (illus. 5) illus. 6 Assembled tent without rainfly. illus. 5 Frame clips Grey poles Grommets for rainfly poles 4 Attach Rainfly – Assemble rainfly poles by interlocking shock- corded pole. – Insert rainfly pole into pole sleeves illus. 10 located at the center edges of the underside of rainfly. (illus. 7), (illus. 8) – Drape rainfly over tent, pole side down. The rainfly poles should cover the door and rear window of tent. – Insert rainfly poles into grommets on tent body. (illus. 6) – Secure rainfly with attachments located on underside of rainfly. – Connect the elastic loops with “S” hooks (found at the rainfly corners) to fabric loops near frame clips. – Stake out all guylines. (illus. 8) – Assemble and insert (short) Vertical Hinged Door Pole through vertical sleeve and into bottom pole stop. Gently apply pressure to insert top end into top pole stop and zip sleeve closed. (illus. 9, 10) Long Door Vertical Door Pole inserts – Assemble and insert (long) Hinged Pole inserts into sleeve Door Pole through curved door sleeve into sleeve and pole and into top pole stop. Gently apply and zips in stops, then pressure to insert bottom end into bottom pole zips in. stop and zip sleeve closed. (illus. 9, 10) illus. 9 Hinged Door – Attach light kit. (See instructions in light kit) Pole Stop illus. 10 Hinged Door Things You Should Know • Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside surfaces of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside your tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent. • Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag. • STAKES SHOULD BE REMOVED BY PULLING ON THE STAKE ITSELF. NEVER PULL ON THE TENT FABRIC OR TENT STAKE LOOP TO REMOVE STAKE. • TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER DURING STORAGE. • Do not leave your tent set-up for weeks at a time, be aware that exposure to the ultraviolet rays of the sun can seriously damage material and/or cause it to become discolored. WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC. This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective. WARNING: Fluorescent tube(s) contain mercury (Hg) and must be recycled or disposed of according to local, state or federal laws. Call (800) 835-3278 or visit for recycling instructions or safe disposal locations. THE COLEMAN CO., INC. 3600 N. Hydraulic • Wichita, Kansas 67219 1-800-835-3278 • MADE IN CH...