Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
SAFETY PRECATIONS • This Power System unit should only be used on a level surface and is intended for indoor use only. Keys Fitness recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning. • Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use this unit with bare feet, sandals, socks or stockings! • Always examine your unit before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the unit. • Service to your Power System unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys Fitness technician. Failure to follow these instructions will void the warranty. • ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 1 Attach main base (1) to rear base (17) using: 2 x (47) Bolt 1 x (27) Plate 4 x (54) Washer 2 x (59) Nylon Locknut STEP 2 Connect main support (2) to main upright (3) using: 2 x (45) Bolt 2 x (54) Washer Then connect to main base (1) using: 2 x (48) Bolt 4 x (54) Washer 2 x (59) Nylon Locknut 2 x (45) Bolt 2 x (54) Washer Slide shaft (26) through pillow block bearings (61) and main upright (3), secure using: 2 x (51) Bolt 4 x (55) Washer 2 x (60) Nylon Locknut Insert stopper slide (8) into the main upright (3) and then attach air cylinder (22) to main upright (3) and stopper slide (8). • ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 3 Attach left arm (4) to shaft (26) using one (49) allen screw (make sure to allow the allen screw to align with the hole in the shaft (26)). This will need to be repeated with the right arm (5) once both arms are connected. Connect left arm (4) and right arm (5) using: 4 x (60) Nylon locknut M12 4 x (55) Wahser 12 2 x (11) Bolt shaft M12 x 300 2 x (12) Spacer tube 2 x (49) Allen screw Both allen screws (49) will need to be aligned with the holes in the shaft and tightened before putting the end caps (33) onto each arm. Insert the brake cable end into the brake handle groove and then connect brake handle (20) to the left arm using : 1 x (42) Bolt 1 x (58) Nylon locknut M6 Back Side • ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 4 Insert the slide tube (19) into the base and secure with pedal pin adjustment. Connect slide tube (19) and seat frame (6) using: 3 x (41) Bolt 5 x (54) Washer 2 x (59) Nylon locknut Attach seat support (7) and back pad frame (9) to the seat frame (6) using: 4 x (66) Bushing 1 x (13) Bolt shaft M10*12*213 2 x (55) Washer 2 x (59) Nylon locknut M10 Attach back pad support (10) to the main upright (3) and the back pad frame (9) using: 1 x (50) Bolt M12*75 1 x (18) Bolt shaft M10*12*200 4 x (66) Bushing 4 x (55) Washer 1 x (60) Nylon locknut M12 2 x (59) Nylon locknut M10 • ASSEMBLY NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. STEP 5 Attach back pad (24) to back pad frame (9) using: 4 x (54) Washer 4 x (46) Bolt Attach seat pad (23) to seat support (7) using: 2 x (54) Washer 2 x (46) Bolt • PARTS LIST # DESCRIPTION QTY # DESCRIPTION QTY base 1 39 spring 1.5*13*43 1 main support 1 40 spring 1.2*12*42 1 main upright 1 41 bolt M10*30 3 left arm 1 42 bolt M6*30 1 right arm 1 43 bolt M6*45 1 seat frame 1 44 bolt M8*13 1 seat support 1 45 bolt M10*15 6 stopper slide 1 46 bolt M10*65 6 back pad frame 1 47 bolt M10*80 2 back pad support 1 48 bolt M10*100 2 bolt shaft M12*300 2 49 allen screw M8*10 2 spacer tube 2 50 bolt M12*75 1 bolt shaft M10*12*213 1 51 bolt M12*135 2 adapter 2 52 shoulder bolt M8*10 2 pin 1 53 washer 11*38*2 2 pedal pin 1 54 washer 11*23*2 23 rear base 1 55 washer 13*26*2 14 bolt shaft M10*12*200 1 56 allen bolt M8*45 1 slide tube 1 57 philip screw M4*5 1 brake handle 1 58 nylon locknut M6 2 clip spring 1 59 nylon locknut M10 10 air cylinder 1 60 nylon locknut M12 8 seat pad 1 61 pillow block bearing 2 back pad 1 62 brake cable 1 middle pad 1 63 bumper 2 shaft 1 64 phillip screw M6*8 4 plate 1 65 jam nut M20*1.5*18 1 plug 40*80 1 66 bushing 12.2*21.8*8 8 plug 50.8*76.2 3 67 allen wrench 1 plug 50.8 6 68 rubber guide sleeve 1 plug OD48 4 69 cabler holder 1 plug OD60 5 70 philip screw M5*5 4 end cap 50.8 4 71 small wheel 1 grip 25*153 2 72 back pad support bumpper 1 wheel 2 73 nylon locknut M8 1 seat pin 1 74 small grip 1 knobl 1 75 rubber spacer 2 grip 25*285 2 76 wrench 1 • EXPLODED VIEW • KEYS FITNESS PRODUCTS, L.P. POWER SYSTEM SERIES LIFETIME WARRANTY This Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty period to the original purchaser is lifetime of the original purchaser. Keys warrants that the Product you have purchased for non-commercial, personal, family, or househould use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship under n...