Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Keys Fitness assures the very best in value, appearance, durability and biomechanics. This manual will guide you through the assembly process. If at any time you are having trouble with the assembly or use of this product, then please contact us at our Keys Fitness Helpline. We have trained service technicians on site to take care of you, our valued customer. REGISTRATION CARD To avoid unnecessary delays in warranty parts and to insure that a permanent record of your purchase is on file with our company, be sure to send in the warranty registration card or register on-line at within 10 days of purchase. KEYS FITNESS Series QUESTIONS? CALL 1-888-380-0482 Monday-Friday 8:30-5:30 Central Time When calling please have the following product information available: Model Name : KF-2060 Serial #: Manufactured Date : PO # : Model Name Decal Location Important Safety Information Prior to assembly, remove components from the box and verify that all the listed parts were supplied. NOTE: Hand tighten bolts and nylon nuts until machine is fully assembled. Read all precautions and instructions in this manual before using this equipment. WARNING! Before using this unit or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. Keys Fitness Products LP assumes no responsibility for personal injury or property damage sustained by or through the use of this product. It is the owner’s responsibility to ensure that all users of this unit have read the Owner’s Manual and are familiar with safety information and precautions. SAFETY PRECAUTIONS • This unit should only be used on a level surface and is intended for indoor use only. Keys Fitness recommends an equipment mat be placed under the unit to protect the floor or carpet and for easier cleaning. • Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use this unit with bare feet, sandals, socks or stockings! • Always examine your unit before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the unit. • Service to your unit should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys Fitness technician. Failure to follow these instructions will void the warranty. Assembly Box 1 Assembly Box 2 Assembly Box 3 Assembly Box 4 Assembly Box 5 Assembly Box 6 10 Assembly Box 8 Box 7 ..........pcs ..........pcs Box 9 Box 10 ..........pcs ..........pcs Box 12 Box 11 ..........pcs ..........pcs 11 Assembly 12 Assembly 13 Assembly 14 Assembly Step 1 Attach Right Base Frame (4) to Rear Frame (1) using two Nuts (144), four Washers (143), and two Bolts (137). Attach Left Base Frame (8) to Rear Frame (1) using two Nuts (144), four Washers (143), and two Bolts (137). Insert Guide Rods (47) into Rear Frame (1). Next, slide Weight Stack Bumpers (99) onto Guide Rods (47). Attach Rear Upright (3) to Rear Frame (1) using two Nuts (144), four Washers (143), and two Bolts (136). Figure 1 15 Assembly Step 2 Slide the weight plates down the Guide Rods (47) in this order - five 15lb Plates (52), nine 10lb Plates (53), five 5lb Plates (54), and the Top Plate (55). Note: Number of weight plates may vary depending on your specific configuration. Attach Top Frame (2) to all four Guide Rods (47) and secure to Rear Upright (3) using two Nuts (144), four Washers (143), and two Bolts (136). Figure 2 16 Assembly Step 3 Attach Front Upright (19) to Seat Pad Support Receptacle (6) using two Nuts (144), four Washers (143), and two Bolts (136). Attach Seat Pad Support Receptacle (6) to Base Frame assembly using two Nuts (144), four Washers (143), and two Bolts (136). Figure 3 17 Assembly Step 4 Attach Main Upright (7) to Seat Pad Support Receptacle using two Nuts (126), four Washers (125), and two Bolts (131). Attach Right Top Frame (5) to Top Frame assembly using two Nuts (144), four Washers (143), and two Bolts (137). Next, use two Washers (143), two Spring Washers (119), and two Bolts (142) to connect Right Top Frame (5) to Main Upright. Figure 4 18 Assembly Step 5 Slide Press Station Base Frame (11) over Press Arm Support (10). Next, attach both pieces to Base Frame using two Nuts (144), four Washers (143), and two Bolts (134). Install Left Top Frame over Press Arm Support (10) and Top Frame assembly. Secure top section using two Nuts (144), four Washers (143), and two Bolts (137). Next, Secure lower section using two Nuts (144), four Washers (143), and two Bolts (136). Secure top of Guide Rods (47) using two Washers (143), two Spring Washers (119), and two Bolts (142). Figure 5 19 Assembly Step 6 Attach Pec Dec Mount (21) onto Seat Pad Support Receptacle using two Nuts (144), four Washers (143), and two Bolts (136). Secure in place with one Washer (129), one Spring Washer (119), and one Bolt (137). Figure 6 20 Assembly Step 7 Attach Right and Left Leg Hol...