Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Anleitung Zusammenfassung
LAT BARBRACKET ASSEMBLYUPPER PULLEY ASSEMBLYFLAT WASHER (B) NYLON NUT (C) FLAT WASHER (B) SUPPORTPLATEBOLT (A) FLAT WASHER (B) BOLT (D) FLAT WASHER (B) NYLON NUT (C) ASSEMBLY STEP 3 HARDWARE BAG 2 CONTENTS : NYLON NUT (C) Qty: 2FLAT WASHER (B) Qty: 4BOLT (A) Qty: 2SCREW (F) Qty: 4 RADIAL ARM ASSEMBLYNYLON NUT (C) FLAT WASHER (B) FLAT WASHER (B) BOLT (A) SEAT WELDMENT SETFRONT COVERBACK COVERSCREW (F) STEP 3-D: INSTALLING THE STOPPER: RADIAL ARM ASSEMBLYSTOPPER Open HARDWARE BAG 2. Attach SEAT WELDMENT SET. Attach Cover to bolted joint using 4 SCREWS (F). Remove STOPPER from front side of RADIAL ARM ASSEMBLY and reinstall on back side of RADIAL ARM ASSMBLY. Attach RADIAL ARM ASSEMBLY to CENTER SUPPORT FRAME using 2 BOLTS (A), 4 FLAT WASHERS (B) and 2 NYLON NUTS (C). SEAT SET SAFETY PINFLAT WASHER (B) NYLON NUT (C) CENTER SUPPORT FRAMESEAT WELDMENT SETBOLT (G) FLAT WASHER (B) LEG EXTENSION/ CURL DOWN TUBECABLE ATTACHMENT ASSEMBLY STEP 4 HARDWARE BAG 3 CONTENTS : NYLON NUT (C) Qty: 1FLAT WASHER (B) Qty: 2BOLT (G) Qty: 1 Open HARDWARE BAG 3. Attach LEG EXTENSION/CURL DOWN TUBE to SEAT ASSEMBLY using 1 BOLT (G), 2 FLAT WASHERS (B) and 1 NYLON NUT (C). NOTE: Position the LEG EXTENSION/CURL DOWN TUBE so the cable attachment is facing the gym. Insert SEAT SET SAFETY PIN. ASSEMBLY STEP 5 HARDWARE BAG 4 CONTENTS : FLAT WASHER (B) Qty: 6SCREW (H) Qty: 2BOLT (N) Qty: 2 END COVERLEG PADLEG EXTENSION/ CURL DOWN TUBESEAT BOTTOM PADSEAT BACK PADFLAT WASHER (B) SCREW (H) FLAT WASHER (B) SEAT WELDMENTNYLON NUT (C)BOLT (N) Open HARDWARE BAG 4. Attach SEAT BACK PAD to CENTER SUPPORT FRAME using 2 SCREWS (H), 2 FLAT WASHERS (B). Attach SEAT BOTTOM PAD to SEAT WELDMENT using 2 BOLTS (D), 4 FLAT WASHERS (B) and 2 NYLON NUTS (C). Install assembled seat into gym. Install LEG PADS to LEG EXTENSION/CURL DOWN TUBE as shown in diagram. ASSEMBLY STEP 6 HARDWARE BAG 5 CONTENTS : FLAT WASHER (J) Qty: 8NYLON NUT (K) Qty: 4BUMPERQty: 2BOLT (I) Qty: 4 BUMPERGUIDE RODWEIGHT PLATETOP WEIGHTBAYONETSELECTOR PINNYLON NUT (K) FLAT WASHER (J) FLAT WASHER (J) SCREW (I) FLAT WASHER (J) SCREW (I) Open HARDWARE BAG 5. Insert each GUIDE ROD into the BASE FRAME as shown in diagram. NOTE: Ensure that holes in GUIDE RODS are located at the top. Install rubber BUMPER onto each GUIDE ROD. Install each WEIGHT PLATE onto GUIDE RODS NOTE: Ensure that each WEIGHT PLATE’s selector pin slot faces downward. Insert each GUIDE ROD into the corresponding hole in the UPPER PULLEY ASSEMBLY. Secure GUIDE RODS in UPPER PULLEY ASSEMBLY using 2 BOLTS (I), 4 FLAT WASHERS (J) and 2 NYLON NUTS (K). NOTE: Ensure that each bolt is inserted through the hole at the top of the GUIDE ROD. Install 2 BOLTS (I), 4 FLAT WASHERS (J) and 2 NYLON NUTS (K) into the BASE FRAME as shown in diagram. Tighten all hardware. ASSEMBLY STEP 7 HARDWARE BAG 6 CONTENTS : Open HARDWARE BAG 6. Remove nylon nut and threaded screw from end of CABLE A. Insert cable end into LAT BAR ASSEMBLY BRACKET pulley as shown in diagram. NOTE: After passing through second pulley bracket, DUAL FLOATING PULLEY BRACKET must be installed. Re-install threaded screw and nylon nut before threading cable into TOP WEIGHT PLATE. NOTE: Always maintain at least .. of weight cable screw in TOP WEIGHT PLATE for saftey. Hook LAT BAR on to cable using the HOOK and rest in craddle. CABLE AQty: 1 CABLE ALAT BARRUBBER STOPBALLNYLON NUT (C) FLAT WASHER (B) DUAL FLOATINGPULLEY BRACKETLAT BAR / WEIGHTCABLE SCREW AND NUTTOP WEIGHTTHREADHOOKCLEVISFLAT WASHER (B) SCREW (E) ASSEMBLY STEP 8 HARDWARE BAG 7 CONTENTS : CABLE BQty: 1 RUBBER STOPBALLNYLON NUT (C) FLAT WASHER (B) CABLE BGRIPHOOKCLEVISFLAT WASHER (B) SCREW (E) Open HARDWARE BAG 7. Remove nylon nut, threaded screw and ball from end of CABLE B. Route CABLE B through the pulley system in the RADIAL ARM ASSEMBLY as shown in diagram. After CABLE B routing is complete replace nylon nut, threaded screw and ball on end of cable. Hook HANDLES on to cable using the 2 HOOKS. ASSEMBLY STEP 9 HARDWARE BAG 8 CONTENTS : Open HARDWARE BAG 8. Remove nylon nut, threaded screw and ball from end of CABLE C. Attach threaded cable end to SINGLE FLOATING PULLEY BRACKET. Route CABLE C through pulley system of BASE FRAME up through the DUAL FLOATING PULLEY BRACKET and back to BASE FRAME and CENTER SUPPORT FRAME as shown in diagram. After CABLE C routing is complete replace nylon nut, threaded screw and ball on end of cable. Hook the LEG EXTENSION/CURL DOWN TUBE to the end of the cable using the HOOK and the EXTENSION CABLE. CABLE CQty: 1 RUBBER STOPBALLNYLONNUT (C) FLATWASHER (B) HOOKEXTENSIONCABLELEG EXTENSION/ CURL DOWN TUBECABLE SCREWSINGLE FLOATINGPULLEY BRACKETCABLE CCLEVISFLAT WASHER (B) SCREW (E) INTRODUCTION IMPORTANT PRECAUTIONS ASSEMBLY BEFORE YOU BEGIN CONDITIONING GUIDELINES TROUBLESHOOTING & MAINTENANCE LIMITED WARRANTY 17 ASSEMBLY STEP 10 HARDWARE BAG 9 CONTENTS : FLAT WASHER (M) Qty: 8SCREW (L) Qty: 8 RIGHT SHROUDSCREW (L) FLAT WASHER (M) LEFT SHROUD Open HARDWARE BAG 9. Install WEIGHT SHROUDS a...