Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
X 1 IN. BUSHING PULLEY........................(Cl 162-1 4-1/2 O.D. X 1 IN. BUSHING PULLEY........................(Cl 161-1 20 .. 6 .. 2 3 PBF058 SELECTORIZED LAT MACHINE ASSEMBLY INSTRUCTIONS IMPORTANT: THE BODYSMITH SELECTORIZED LAT MACHINE MUST BE ASSEMBLED ON A FLAT LEVEL SURFACE TO ASSURE ITS PROPER FUNCTION. • PARABODY, INC. STRONGLY RECOMMENDS THAT THIS PRODUCT BE ASSEMBLED BY TWO PERSONS TO AVOID POSSIBLE INJURY. *** IMPORTANT *** KEEP ALL LOOSE FRAME CONNECTIONS LOOSE UNTIL INSTRUCTED IN THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN 1. Insert one (1) 2 IN. SQ. END CAP into the front end of the BASE SECTION, and two (2) 1-1/2 X 2-1/2 IN. END CAPS into the ends of the BASE LEG. 2. Apply two (2) 2-1/2 X 5-1/2 IN. NON SKID STRIPS to the FOOT BRACE TUBE on the BASE SECTION as shown on drawing. 3. LOOSELY assemble the REAR UPRIGHT to the BASE SECTION, using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, two (2) 3/8 IN. LOCK WASHERS, and two (2) 3/8 IN. NUTS. 4. LOOSELY assemble the FRONT UPRIGHT to the BASE SECTION, using two (2) 3/8 X 3 IN. BOLTS, four (4) 3/8 IN. WASHERS, two (2) 3/8 IN. LOCK WASHERS, and two (2) 3/8 IN. NUTS. 5. Insert one (1) 1-3/4 IN. SQ. END CAP into the end of the SEAT SUPPORT TUBE on the FRONT UPRIGHT. 6. LOOSELY attach one (1) 4-1/2 O.D. X 1 IN. BUSHING PULLEY to the LOW ROW PULLEY HOUSING, on the FRONT UPRIGHT, using one (1) 3/8 X 1-3/4 IN. BOLT, one (1) 3/8 IN. LOCK WASHER, and one (1) 3/8 IN. NUT. (SEE DRAWING) 7. LOOSELY attach one (1) 4-1/2 O.D. X 1 IN. BUSHING PULLEY, and one (1) CABLE RETAINING CLIP to the PULLEY BRACKET on the FRONT UPRIGHT, using one (1) 3/8 X 1-3/4 IN. BOLT, one (1) 3/8 IN. LOCK WASHER, and one (1) 3/8 IN. NUT. (SEE DRAWING) 4 058 SELECTOR!ZEI) LAT MACHINE ASSEMBLY INSTRUCTIONS 8. Attach eight (16) PARAGLIDE STRIPS (TWO AT EACH CORNER) to the ADJUSTABLE ROLLER PAD SLIDE as shown in (DETAIL A) using the following steps: A. Thoroughly clean all inside surfaces where the PARAGLIDE STRIPS are to be attached. B. Remove the paper backing from the PARAGLIDE STRIPS and firmly apply them to all shown surfaces (16 places). 9. Attach two (2) 4 X 7 IN. ROLLER PADS to the ADJUSTABLE ROLLER PAD SLIDE using two (2) STAR LOCK COLLARS. 10. Assemble the SPRING PIN ASSEMBLY to the ADJUSTABLE ROLLER PAD SLIDE, using one (1) KNOB, one (1) PLUNGER, one (1) SPRING, one (1) SPACER, and one (1) COTTER PIN, using the following steps: A. Assemble the KNOB to the PLUNGER.. B. Insert the PLUNGER through the first hole of the HOUSING. C. Slip the SPRING and the SPACER over the end of the PLUNGER. (IN THAT ORDER) D. Insert the PLUNGER through the second hole of the HOUSING. E. Pull back SPACER on the PLUNGER and insert the COTTER PIN through the hole. F. (SEE DETAIL A) 11. Insert one (1) 1-1/2 IN. SQ. END CAP into the top end of SPRING PIN HOUSING on the ADJUSTABLE ROLLER PAD SLIDE. (SEE DETAIL A) 12. Slide the ADJUSTABLE ROLLER PAD SLIDE down over the FRONT UPRIGHT, and engage the SPRING PIN into any adjustment hole. 13. Slide the two (2) ROD END COVERS over the ends of the LAT BAR HOLDER on the TOP BOOM. 14. LOOSELY assemble the TOP BOOM to the REAR and FRONT UPRIGHTS, using four (4) 3/8 X 3 IN. BOLTS, four (4) 1/2 IN. WASHERS, four (4) 3/8 IN. LOCK WASHERS, and four (4) 3/8 IN. NUTS. (NOTE: THE FOUR (4) 1/2 IN. WASHERS ARE TO BE USED IN BETWEEN THE TOP BOOM AND THE FRONT UPRIGHT ON BOTH SIDES) 15. SECURELY assemble the WEIGHT STACK SHAFT into the HEAD PLATE using one (1) 3/8 X 1 -1/2 IN. BOLT one (1) 3/8 IN. LOCK WASHER, and one (1) 3/8 IN. WASHER. 16. Press two (2) WEIGHT PLATE BUSHINGS each, into the top of twenty (20) WEIGHT PLATES. (40 BUSHINGS TOTAL) (SEE DETAIL B) 17. Place each of the two (2) WEIGHT STACK CUSHIONS (RADIUS EDGES FACING UP) over the GUIDE ROD HOLES on the BASE SECTION. Insert each of the two (2) GUIDE RODS through the WEIGHT STACK CUSHIONS and into the BASE SECTION. (NOTE: LUBRICATE GUIDE RODS WITH A SILICON OR TEFLON SPRAY THAT IS AVA] LABLE AT MOST HARDWARE STORES) 18. USING EXTRFMF. CARE slide each of the twenty (20) WEIGHT PLATES down over the GUIDE RODS onto the BASE SECTION. (NOTE: THE KEY HOLE OF THE WEIGHT PLATES SHOULD ALL BE FACING THE SAME WAY SEE DRAWING) 5 WEltHT PLATE BUSH IN65 ( 2 PER PLATE) 10 LB. WEIÛHT PLATE (2.01 TOP BOOM ÏVzO.L.} UN.BUSHIN6 PULLEY (Ml VS X 3 EOLT (21 ■5/a X 3 BOLT (MI SPACER. SPRING Z05- I RUBBER O-RINü fZl REVISIONS REV DESCRIPTION CHG NO APPD OATE A NEW P.E_LEASE 073. \ 5 düÚ/Z}WO££¿ ÙN FRÖNT UPR&HT ÙELEfcCZÏHOœ^ ON 5AS£ 1SZÍ \ t ACiD ?£RAG»L1DE STRIPS IBM I & '¿z /9¿ D. ADD U.S.A. LABGjL W14- 3xy ‘Hz E ADD DET^L "F“ 2t5B Mb ft/ 73 LOCK WASHER % MUT