Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
STEP 4 • Apply eight 1-3/4 x 3/4" PARAGLIDES (70) to the INSIDE of RECEIVING TUBE (13) as shown in FIGURE 4. (NOTE: Throughly clean the inside surface before attaching PARAGLIDES.) 49 42 1/2 X 3” 3/8 X 3-3/4” 40 86 79 52 51 29 58 51 10 9 48 13 70 16 3 FIGURE 5 7 FIGURE 6 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 5 • Insert two 1/2" FLANGE BEARINGS (67) into RECEIVING TUBE (13). • Attach RECEIVING TUBE (13) to PRESS ARM LEVER (9) using one 1/2 X 3-1/2" BOLT (43), and 1/2" LOW HEIGHT LOCKNUT (50). (NOTE: Securely tighten, then back nut off 1/4 turn to allow the RECEIVING TUBE (13) to rotate freely.) • Insert the ADJUSTMENT TUBE (6) into the RECEIVING TUBE (13) as shown in FIGURE 5. • Slide one 3/4 DIA X 11" SHAFT (29) through PRESS ARM (8) & tube on REAR UPRIGHT (16). See FIGURE 6. • Insert two 1/2" FLANGE BEARINGS (67) into PRESS ARM (8). STEP 6 29 8 16 9 13 6 67 50 1/2 X 3-1/2” 43 67 1/2” LOW HEIGHT 8 FIGURE 8 FIGURE 7 • Attach ADJUSTMENT SLIDE (6) to PRESS ARM (8) using one 1/2 X 3-1/2" BOLT (43), and 1/2" LOW HEIGHT LOCKNUT (50). (NOTE: Securely tighten, then back nut off 1/4 turn to allow the PRESS ARM (8) to rotate freely.) STEP 7 STEP 8 • Insert the PUSH/PULL CABLE through the bottom of the PRESS ARM (8) up to the CONTROL LEVER (59) and hold in place with one E-RING (62) as shown in FIGURE 8. • Securely assemble the PUSH/PULL CABLE to the CONTROL LEVER (59) using one 3/8 IN. JOINT CONNECTOR CAP (61), one #8 INT. TOOTH LOCK WASHER (63), and one 8-32 X 3/16 IN. SCREW (60) as shown in FIGURE 8. • Slide one 4” VINYL SLEEVE (64) over the CONTROL LEVER (59). Then SECURELY assemble the CONTROL LEVER (59) to the TAB on the PRESS ARM (8) using one 3/8” JOINT CONNECTOR CAP (61), one #8 INT. TOOTH LOCK WASHER (63), and one 8-32 X 3/16 IN. SCREW (60) as shown in FIGURE 8. 50 8 43 1/2 X 3-1/2” 6 64 TAB 8 60 61 PUSH/PULL CABLE 63 59 62 1/2” LOW HEIGHT 9 FIGURE 9 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 10 DETAIL 9 DETAIL 9 1/4” NUTS PUSH/PULL CABLE SPRING PIN ASSEMBLY 13 DO NOT OVERTIGHTEN! Assemble the PUSH/PULL CABLE from the PRESS ARM (8) to the SPRING PIN HOUSING and to the L-BRACKET on the RECEIVING TUBE (13) as shown on FIGURE 9 and DETAIL 9 using the following steps: STEP 9 Thread the first 1/4-28 IN. NUT to the bottom of the threaded end of the CABLE. Allow the other 1/4-28 IN. NUT to hang loose on the exposed CABLE until the SPRING PIN ASSEMBLY is attached. Securely assemble the SPRING PIN ASSEMBLY to the SPRING PIN BARREL. (!!! IMPORTANT !!! TIGHTEN THE NUT OF THE SPRING PIN ASSEMBLY SECURELY) Swing the PRESS ARM (8) up until the SPRING PIN of the PUSH/PULL CABLE engages in one of the adjustment holes. Thread the second 1/4-28 IN. NUT onto the threaded end of the CABLE, and cinch the two 1/4-28 IN. NUTS around the flat. Use the extra thread on the end of the CABLE to adjust out slack. ( !!! DO NOT ADJUST OUT TO FAR !!! ALWAYS ALLOW SPRING PIN ASSEMBLY TO FULLY ENGAGE) STEP 10 • Securely tighten two 5/32” SET SCREWS (65) and insert two 3 X 2” END CAPS (75) into the open ends of PRESS ARM (8) as shown in FIGURE 10. • Securely tighten two 5/32" SET SCREWS (65) and insert two 2” SQ. END CAPS (76) into the open ends of PRESS ARM LEVER (9) as shown in FIGURE 10. • Securely tighten one 3/8 X 1” BOLT (35), one 3/8” WASHER (51), and one 3/8” LOCKNUT (48) to the bottom of ADJUSTMENT SLIDE (6) as shown in FIGURE 10. • Insert one 1-3/4” SQ. END CAP (77) into the end of ADJUSTMENT SLIDE (6) as shown in FIGURE 10. 48 76 51 75 65 65 77 6 9 8 3/8 X 1” 35 8 13 10 FIGURE 11 STEP 11 • Securely assemble the PEC SEAT PAD (27) to the FRONT UPRIGHT (11) as shown, using two 3/8 X 4” BOLTS (41), and two 3/8” WASHERS (51) as shown in FIGURE 11. • Assemble two ROLLER PADS (31) to the FRONT UPRIGHT (11) using one 16” TUBE (34), and two STARLOCK COLLARS (75) as shown in FIGURE 11. STEP 12 • Loosely attach FRONT UPRIGHT (11) to the BASE (10) using two 3/8 X 3” BOLTS (39), four 3/8” WASHERS (51), and two 3/8” LOCKNUTS (48) as shown in FIGURE 12. (NOTE: Make sure cable is routed under the bolts.) • Loosely attach FRAME SUPPORT (1) to the FRONT UPRIGHT (11) using two 3/8 X 4” BOLTS (41), four 3/8” WASHERS (51), and two 3/8” LOCKNUTS (48) as shown in FIGURE 12. • Loosely attach FRAME SUPPORT (1) to the BASE (10) using one 3/8 X 3” BOLT (39), two 3/8” WASHERS (51), and one 3/8” LOCKNUT (48) as shown in FIGURE 12. (NOTE: Make sure cable is routed under the bolts.) FIGURE 12 • All WASHERS & LOCKNUTS are 3/8” WASHERS (51) & 3/8” LOCKNUTS (48). 3/8 X 3” 39 41 3/8 X 4” 11 10 1 11 27 75 31 34 3/8 X 4” 41 51 11 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 13 FIGURE 14 STEP 14 • Snap two WEIGHT PLATE BUSHINGS (47) each, into the PARABODY side of fifteen WEIGHT PLATES (74) as shown in FIGURE 14. STEP 13 • Loosely assemble four 3-1/2” PULLEYS (79) to the slots in TOP BOOM (7) using four 3/8 X 2-3/4” BOLTS (38), eight 3/8” FLANGE SPACERS (66), and four 3/8” LOCKNUTS (48) as shown in FIGURE 13. (NOTE: Make sure the cable is routed under all t...