Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
KIT I ASSEMBLY INSTRUCTIONS Part # 6747801 1 Revision: 09/25/97 ]IMPORTANT NOTES] WELCOME TO THE WORLD OF $~eiOU$ $~l~i!t Please note: *Thank you for purchasing the 435103 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these roles: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. I Tools Required for Assembly i * Rubber mallet or hammer * 3/4" wrench * 9/16" wrench * Ratchet with 3/4" and 9/16" sockets * 7/32" Allen wrench * Adjustable wrench * Tape measure Bolt Length Ruler I " NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF Tl=l-E H~EAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: [ 112 [ 1/2 ~ 1/2 I 1/2 I 1/2 I 1/2 0I1 4 6 I ’ ’ 2 PARTS LIST KEY PART# DESCRIPTION QTY KEY PART# DESCRIP’.rlON QTY 1 6747603 FRONT LEG 1 9 6535301 1/4" CAP NUT 1 2 3116202 3-1/2" PULLEY 2 10 3102501 3/8" W, HER 4 3 3108102 QUICK DISCONNECT LINK 1 11 3102802 3/8" LOCKNUT 2 . 4 6427101 KEYHOLE CLEVIS 1 12 3102502 1/2" W, HER 4 5 3117305 CLEVIS PIN 1 13 3102801 1/2" LOCKNUT 4 6 3112901 COTTER PIN 1 14 3102933 3/8X2 BOLT 2 7 6732901 TENSION CORD 1 15 3102910 1/2X3 BOLT 4 8 6747901 LEGPRESS CABLE 1 NOTE: The LEG PRESS ATTAClqTMENT (832101) must be assembled before connecthlg it to the PARABODY 425103 t~OME GYM 3/8" X 1" HEAD CAP SCREW 3/8" X 1" BUTTON HEAD CAP SCREW FIGURE 1 STEP 1 . REMOVEthe four 3/8" X 1" BUTTON HEAD CAP SCREWS from the HOME GYM. See FIGURE 1. rear SHROUD. Remove the SHROUDfrom the 425103 3 FIGURE 2 STEP 2 . If the 445103 SECOND OPTION not installed, the rear opening must be removed. AI?ply pressure STACK is SHROUD to the bottom of the SHROUD where the "V" groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 3. 1/2 [ 1/2 [ 1/2 I 1/2 [ 1/2 6 3/8 X 2"~ BASE FIGURE 3 ’,TEP 3 . SECURELYattach LOCKNUT(11). one 3-1/2" PULLEY(2) See FIGURE to the BASE using one 3/8 X 2" BOLT (14), two 3/8" WASHERS(10), and one . . . SECURELYattach one 3-1/2" PULLEY(2) to the FRONT LEG (1) using one 3/8 X 2" BOLT (14), two 3/8" WASHERS (10), and one 3/8" LOCKNUT (11). See FIGURE Attach the open end of PRESS LINK CABLE (8) to the QUICK DISCONNECT LINK (3). See FIGURE SECURELYtighten the QUICK DISCONNECT (3) the tab on the FRONT LEG (1) as shwon in FIGURE " TIGHTEN! FIGURE 4 1/2 X 3"(~ ~LEG PRESS FIGURE 5 STEP 5 . SECURELYattach the LEG PRESS to the FRONT LEG (1) using two 1/2" X 3" BOLTS (15), two 1/2" 1/2" LOCK NUTS (13). See FIGURE . Route LEG PRESS CABLE (8) around the3-1/2" PULLEYon the LEG PRESS and UNDER the 3-1/2" LEG (1) as shown in FIGURE WASHERS(12), and PULLEYon the FRONT 1/2 [ 1/2 [ 1/2 [ 1/2 [ 1/2 ] 1/2 ] 1 4 5 6 [ I I ~ I I 6 BASE FIGURE 6 STEP 6 . SECURELY FRONT to 425 BASEusing two 1/2 X 3" BOLTS two 1/2" (12) and two 1/2" attachthe LEG (1) (15), WASHERS NUTS (13). See FIGURE . Route LEG PRESS CABLE (8) under the 3-1/2" PULLEYon the 425 BASE as shown in FIGURE 7 FIGURE DETAIL 7 \ \ I / / LEG CABLE LEG PRESS CABLE CABLE CABLE STEP 7 . Run the LEG PRESS CABLE (8) through the correct hole on the d-ring and attach one KEYHOLE CLEVIS(4) to the end of LEG PRESS CABLE (8). See FIGURE 7 & DETAIL 1/2 ] 1/2 [ 1/2I [ 1/2 I :1/2 [ 345 6 8 LEG CABLE LEG CABLE ~ CABLE FIGURE 8 CABLE STEP 8 . Attach one TENSION CORD(7) FIGURE 8. to the KEYHOLECLEVIS (4) using one CLEVIS PIN (5) and one COTTER PIN (6) as 9 FIGURE 9 BOOM LEG PRESS CABLE STEP 9 . CAREFULLYattach the TENSIONCORD(7) to the corresponding small shaft on the TOP BOOM using one 1/4" CAP NUT (9) as shown in FIGURE 9. [ 1/2 ] 1/2 [ 1/2I 1/2 [ 1/2 [ 1,’2 2 I 5 , , , I , , , 10 3/8" X 1" BUTTON~"~ HEAD CAP SCREW 3/8",X 1" BUTTON HEAl3 CAP SCREW SPRING PIN ADJUSTMENT FIGURE 10 STEP 10 . SECURELY the four previously removed 3/8 X 1" BUTTON CAP SCREWS to the rear S[]?,OUD. See FIGURE attach HEAD 10. . The 832 LEG PRESS is equipped with a spring pin adjustment to accommodate different sized users and allow easy entry and exit from the machine. To use, you must slightly push against the foot plates to take tension off the pin. Thank you for purchasing the Parabody 435103 Leg Press Adapter Kit. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328...