Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
BOLT LENGTH BOLT LENGTH RULER: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 2 STEP 1 FIGURE 1 PART # 6747708 3116201 3108102 6427101 3118701 3201501 6271801 6747901 KEY 1 2 3 4 5 6 7 8 QTY 1 2 1 1 1 1 1 1 PART # 3102701 3102501 3102802 3102502 3102801 3102902 3102910 3102909 DESCRIPTION 3/8” HEX NUT 3/8” WASHER 3/8” LOCKNUT 1/2” WASHER 1/2” LOCKNUT 3/8 X 2-1/4” BOLT 1/2 X 3” BOLT 3/8 X 1” QTY 2 3 2 4 4 2 4 1 DESCRIPTION FRONT LEG 3-1/2” PULLEY QUICK DISCONNECT LINK KEYHOLE CLEVIS 2” PULLEY SWIVEL SNAP 72”ELASTIC CORD LEG PRESS CABLE KEY 9 10 11 12 13 14 15 16 NOTE: The LEG PRESS ATTACHTMENT (100101) must be assembled before connecting it to the PARABODY 660101 HOME GYM PARTS LIST • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the rear SHROUD. Remove the SHROUD from the 660101 HOME GYM. See FIGURE 1. REAR SHROUD 3/8” X 1” BUTTON HEAD CAP SCREW 3 3/8” X 1” BUTTON HEAD CAP SCREW FIGURE 2 REAR SHROUD FIGURE 2 REAR SHROUD STEP 2 • If the 663101 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2. 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 4 FIGURE 3 STEP 3 • Remove two 3/8” LOCK NUTS, two 3/8” HEX NUTS, two SWIVEL SNAP (keep elastic cords attached), two 3/ 8 X 1/2” SPACERS, and one 3/8” THREADED SHAFT from the bracket on the BASE as shown in FIGURE 3. BASE 5 HEX NUT • Discard the two 3/8 X 1/2” SPACERS. HEX NUT 3/8 X 1/2” SPACERS (DISCARD) 3/8” THREADED SHAFT SWIVEL SNAP 3/8” LOCK NUT SWIVEL SNAP 3/8” LOCK NUT ELASTIC CORD 6 FIGURE 4 BASE HEXNUT 3/8” LOCK NUT 2 STEP 4 • Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two previously removed 3/8” LOCK NUTS to the previously removed 3/8” THREADED SHAFT as shown in FIGURE 4. HEXNUT 3/8” LOCK NUT 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 3/8” THREADED SHAFT SWIVEL SNAP SWIVEL SNAP FIGURE 5 STEP 5 • Remove one 3/8 X 2” BOLT, two 3/8” WASHERS, one 2-7/8” L-BRACKET, one 4-1/2” PULLEY, and one 3/8” LOCK NUT from the upper flat on the BASE as shown in FIGURE 5. BASE 3/8” WASHER 4-1/2” PULLEY 3/8” WASHER 3/8” LOCK NUT 2-7/8” L-BRACKET 3/8” X 2” BOLT FIGURE 7A (WITHOUT 663101 SECOND STACK OPTION) STEP 7A 3/8” LOCK NUT TOP BOOM 9 3/8” HEX NUT • SECURELY assemble one 2” PULLEY (5) to the 3/8” THREADED SHAFT on the TOP BOOM using one previously installed 3/8” WASHER, one 3/8” HEX NUT (9) and one previously installed 3/8” LOCK NUT as shown in FIGURE 7A. 5 3/8” WASHER FIGURE 6 STEP 6 • SECURELY assemble the previously removed 4-1/2” PULLEY to the BASE using one 3/8 X 2-1/4” BOLT (14), two previously removed 3/8” WASHERS, one previously removed 2-7/8” L-BRACKET, one SWIVEL SNAP (6), one 3/8” HEX NUT (9), and one previously removed 3/8” LOCK NUT. See FIGURE 6. BASE 14 3/8 X 2-1/4” 3/8” WASHER 4-1/2” PULLEY 2-7/8” L-BRACKET 6 9 HEX NUT 3/8” LOCK NUT • If the 663101 SECOND STACK OPTION is installed follow STEP 7B . 3/8” WASHER • Remove one 3/8” WASHER and one 3/8” LOCK NUT from the 3/8” THREADED SHAFT on the TOP BOOM. 7 FIGURE 7B (WITH 663101 SECOND STACK OPTION) STEP 7B • If the 663101 SECOND STACK OPTION is NOT installed proceed to STEP 8 . TOP BOOM 3/8” X 1” 16 10 5 11 3/8” LOCK NUT • SECURELY assemble one 3/8 X 1” BOLT (16), one 3/8” WASHER (10), one 2” PULLEY (5) and one 3/8” LOCK NUT (11) to the bracket on the TOP BOOM as shown in FIGURE 7B. STEP 8 • SECURELY attach one 3-1/2” PULLEY (2) to the FRONT LEG (1) using one 3/8 X 2-1/4” BOLT (14), two 3/8” WASHERS (10), and one 3/8” LOCK NUT (11). See FIGURE 8. • Attach the open end of PRESS LINK CABLE (8) to the QUICK DISCONNECT LINK (3). See FIGURE 8. • SECURELY tighten the QUICK DISCONNECT (3) to the tab on the FRONT LEG (1) as shown in FIGURE 8. FIGURE 8 2 3/8 X 2-1/4” 14 SECURELY TIGHTEN! 8 10 10 11 1 3 8 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 9 STEP 9 FIGURE 9 • Route LEG PRESS CABLE (8) around the 3-1/2” PULLEY on the LEG PRESS and UNDER the 3-1/2” PULLEY on the FRONT LEG (1) as shown in FIGURE 9. • SECURELY attach the LEG PRESS to the FRONT LEG (1) using two 1/2” X 3” BOLTS (15), two 1/2” WASHERS (12), and two 1/2” LOCK NUTS (13). See FIGURE 9. LEG PRESS 1/2 X 3” 15 13 12 8 1 10 FIGURE 10 STEP 10 • SECURELY attach the FRONT LEG (1) to 660 BASE using two 1/2 X 3” BOLTS (15), two 1/2” WASHERS (12) and two 1/2” LOCK NUTS (13). See FIGURE 10. • Route LEG PRESS CABLE (8) under the 3-1/2” PULLEY on the 425 BASE as shown in FIGURE 10. 8 13 12 1 1/2 X 3” 15 BASE 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 11 STEP 11 FIGURE 11 DETAIL 11 SEE DETAIL 11 LEG CABLE LAT CABLE PRESS CABLE D-RING • Run the LEG PRESS CABLE through the correct hole on the d-ring and attach one KEYHOLE CLEVIS to the end of the LEG PRESS CABLE. See FIGURE 11 & DETAIL 11. (NOTE: If the 663101 SECOND STACK kit is installed, evenly space the LAT & LEG EXT. CABLES on the D-RING) FIGURE 12 STEP 12 LEG PRESS CABLE • Assemble one 72” ELASTIC CORD...