Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
This product must be assembled on a flat, level surface to assure its proper function. * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 5. Consult your physician before beginning any exercise program. Tools Required for Assembly * Rubber mallet or hammer * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * 5/32” Allen wrench * Adjustable wrench * Tape measure Bolt Length Ruler NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH BOLT LENGTH RULER: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 2 PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 6874903 FRAME SUPPORT 1 52 3102502 1/2” WASHER 14 6683302 WOLFF SLEEVE 1 53 3102503 3/4” WASHER 2 6682803 WEIGHT STACK BASE 1 54 3109602 PAL NUT 1 6832203 LEG CURL/EXTENSION 1 55 6686301 1/2” DIA U-PIN 1 6686802 PULLEY BRACKET 1 56 6075906 CHAIN 1 6679503 ADJUSTMENT SLIDE 1 57 6214401 WEIGHT STACK PIN 1 6678603 TOP BOOM 1 58 6533501 CABLE RETAINING CLIP 5 6683103 PRESS ARM 1 59 6321201 CONTROL LEVER 1 6680402 PRESS ARM LEVER 1 60 3119201 8-32 X 3/16” SCREW 2 6682103 BASE 1 61 3226301 3/8” JOINT CONNECTOR CAP 2 6682503 FRONT UPRIGHT 1 62 3117901 E-RING 1 6681303 LEVER STOP 1 63 3114407 #10 FLAT WASHER 2 6680202 RECEIVING TUBE 1 64 3118401 4” VINYL CAP 1 6874502 BACK PAD SUPPORT 1 65 3106803 5/16” SET SCREW 4 6874603 LEG SUPPORT 1 66 6480301 3/8” FLANGE SPACER 14 6680903 REAR UPRIGHT 1 67 6020601 1/2” FLANGE BEARING 6 6680803 BEARING HOUSING 1 68 6019701 3/4” THRUST BEARING 2 6681902 PLATE, 1/4 X 2 X 16-1/2” 2 69 3104901 3/4” FLANGE BEARING 8 6532903 PEC ARM RIGHT 1 70 6416601 1-3/4 X 3/4” PARAGLIDE 1 6532803 PEC ARM LEFT 1 71 6412001 SPRING PIN ASSEMBLY 3 6530203 CENTER PULLEY BRACKET 1 72 3103801 5/16” DIA SNAP LINK 4 6594702 FLOATING PULLEY 2 73 3105401 STARLOCK COLLAR 10 6624402 SWIVEL PULLEY BRACKET 1 74 6214501 WEIGHT PLATE 15 6529702 PEC CAM 2 75 6692601 3 X 2” END CAP 2 6275302 LAT BAR 1 76 6405201 2” SQ. END CAP 2 6654302 33-1/2 X 9-1/2” BACK SEAT PAD 1 77 6236701 1-3/4” SQ END CAP 1 6597402 15-1/2 X 10-1/2” PEC SEAT PAD 1 78 6406401 HINGE TAB 2 6681502 15-3/4 X 15-1/2” LEG SEAT PAD 1 79 3116201 3-1/2” PULLEY 19 6690901 3/4 DIA X 11” SHAFT 2 80 6266001 WEIGHT STACK SHAFT 1 6125102 3/4 OD X 16” TUBE 3 81 6714601 HEAD PLATE 1 6194601 4 X 7” ROLLER PAD 8 82 6375801 STRAP AB CRUNCH 1 6176201 PEC DEC ROLLER PAD 2 83 6389701 LOW ROW BAR 1 6523401 3/4 X 72-3/8” GUIDE ROD 2 84 6409101 STRAP ANKLE 1 6375902 WEIGHT STACK SPACER 2 85 3116001 1-1/4” BUMPER RUBBER 1 3102909 3/8 X 1” BOLT 4 86 6270501 4 X 14” NON-SKID 1 3102924 3/8 X 1-3/4” BOLT 8 87 6140701 1 X 1” GLIDE 4 3102933 3/8 X 2” BOLT 4 88 3108002 WEIGHT STACK CUSHION 2 3102922 3/8 X 2-3/4” BOLT 10 89 3117401 CAP PLUG 2 3102904 3/8 X 3” BOLT 6 90 6873801 227-5/8” LEG EXT. CABLE 1 3102905 3/8 X 3-3/4" BOLT 2 91 6687201 72-1/4” AB CABLE 1 3102906 3/8 X 4" BOLT 4 92 6687001 103-1/2” LAT CABLE 1 3102910 1/2 X 3" BOLT 10 93 6535601 77-5/8” PEC DEC CABLE 1 3102943 1/2 X 3-1/2" BOLT 3 94 6189501 WEIGHT STACK LABELS 1 3102917 1/2 X 4" BOLT 2 95 6145801 THUMBSCREW 1 3102937 1/2 X 4-1/2" BOLT 2 96 6382301 WEIGHT PLATE BUSHING 10CT 3 3102901 3/8 X 1-1/4” BOLT 1 97 6866601 BOLT COVER CAP 2 3102949 1/2 X 5-1/2” BOLT 2 98 6866801 BOLT COVER WASHER 2 3102802 3/8” LOCK NUT 29 99 6122702 3/8” X 1/2” SPACER 2 3102801 1/2” LOCK NUT 10 100 6427101 KEYHOLE CLEVIS 1 3102804 1/2” LOW HT. NYLOCK NUT 8 3102501 3/8” WASHER 30 3 FIGURE 1 4 STEP 1 • Securely assemble REAR UPRIGHT (16 ) to BASE (10) using two 1/2 X 3" BOLTS (42), two 1/2" WASHERS (52), and two 1/2" LOCKNUTS (49). • Slide LEG EXT. CABLE ASSEMBLY (90) through openings in BASE (10) as shown in FIGURE 1. • Securely assembe two 3-1/2" PULLEYS (79) into BASE (10) using two 3/8 X 2-3/4" BOLTS (38), four 3/8" FLANGE SPACERS (66), and two 3/8" LOCKNUTS (48). (NOTE: Make sure LEG EXT. CABLE ASSEMBLY (90) is routed under PULLEYS and BOLTS.) • Insert four 3/4" FLANGE BEARINGS (69) into tubes on REAR UPRIGHT (16) as shown in FIGURE 1 90 66 52 48 66 10 49 16 69 3/8 X 2-3/4” 38 79 1/2 X 3” 42 • Slide LEG EXT. CABLE ASSEMBLY (90) through the opening in the end of the BASE (10) as shown in FIGURE 1. 5 FIGURE 2 • Securely assemble one 3-1/2" PULLEY (79) to the top hole of the LEVER STOP (12) using one 3/8 X 3-3/4" BOLT (40), two 3/8" WASHERS (51), one 2-3/8" RETAINING CLIP (58), and one ...