Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Spalding
Dateigröße: 899.12 kb
Dateiname: f06b8410-3f79-b654-d5c6-75bcca47caa4.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Weitere Informationen uber Zusammenbau, undWartung sind von der Webseite des „American derAdresse Die auf diesem Produkt reproduzierten Mitgliedsmannschaften sind Warenzeichen 201241 2/99 andere Formen geistigen Eigentums, TUFF STUFF® und die damit der jeweiligen NBA-Mitgliedsmannschaften deren Genehmigung verwendet. die schriftliche Einwilligung Tochtergesellschaften in Universelle Telefonnummer(Deutschland, BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du systeme elevateur et la visserie doivent etre bien ajustes (serres). A titre d'essai, inserez les gros boulons dans les gros trous des tubes du systeme elevateur, des supports du panneau et des plaques triangulaires. Basculez-les avec precaution en imprimant un mouvement circulaire pour eliminer l'excedent de peinture, si necessaire. .ANTES DE COMENZAR! Para asegurar el optimo rendimiento del sistema del respaldo en el juego, se requiere un ajuste de tolerancia estrecha entre los componentes del elevador y el herraje. Pruebe el ajuste de los pernos grandes en los orificios grandes de los tubos elevadores, soportes del respaldo y placas triangulares. Cuidadosamente muevalos en circulos para eliminar cualquier exceso de pintura, si es necesario. VORBEREITENDE MASSNAHMEN Um sicherzustellen, dass das Korbwandsystem optimal fur den Spielbetrieb geeignet ist, mussen die Komponenten der Verlangerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden. Gro.e Schrauben zur Probe in die gro.en Locher der Verlangerungsrohre, Korbwandklammern und Dreiecksplatte stecken und diese vorsichtig in einer Kreisbewegung hin- und herbewegen, um eventuelle Farbruckstande aus den Bohrungen zu entfernen. 5 05/03 P/N 214949B HARDWARE IDENTIFIER (CONTINUED) Item #13 (10)* Item #10 (3) Item #12 (1) Item #14 (13)* Item #15 (1) Item #16 (2) Item #8 (1) Item #7 (1) Item #19 (1) Item #18 (2) Item #22 (4) * You may have extra parts with this model. HARDWARE IDENTIFIER (CONTINUED) P/N 214949B 05/03 6 HARDWARE IDENTIFIER Item #31 (4) Item #32 (4) Item #34 (5) Item #37 (4) Item #43 (12) Item #39 (1) Item #30 (2) Item #33 (4) Item #38 (6) Item #50 (1) Item #55 (2) Item #36 (6) Item #54 (2) Item #57 (4) Item #64 (2) * You may have extra parts with this model. 7 05/03 P/N 214949B INSTRUCTIONS NOTE: Assemble lanyard (27) to locking pin (28) as shown. IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 19. Apply logo and height indicator labels (52) to adjustment rod (51) as OF THIS OWNERS MANUAL shown. Attach handle parts (48, 49) to adjustment rod (51) with screw (50), carriage bolts (22), and flange nuts (14) as shown. 1. Install wheel axle (6) through wheel carriage (63) and install wheels NOTE: Holes in adjustment rod allow for either rear access or side (5) onto wheel axle (6) with spacers (64) as shown. Secure wheel access. bracket as shown, a deep socket is recommended. 20. Insert handle assembly through pole mount assembly as shown. IMPORTANT! DO NOT OVER TIGHTEN. Lock pole assembly in place at the 10’ (3.05 m) mark with 2. Mark pole sections with tape as shown. pin (60). 3. IMPORTANT! Center alignment slot of middle pole section (2) 21. Attach backboard support brackets (29) to the backboard frame in a lower hole of top pole section (1) as shown. While using bolts (33), spacers (30), and nuts (34) as shown. maintaining alignment, bounce pole top (1) and middle section (2) 22. Attach lower elevator tubes (35) and spring (42) to backboard together as shown until they no longer move toward taped reference support brackets (29) using spacers (32), bolt (36), and nut (38) as mark. Upright assembly. NOTE: Pole sections should have a 3-1/2” shown. NOTE: Rim mounting nuts and bolts (31) supplied with rim (9 cm) minimum overlap. hardware. 4. IMPORTANT! Center alignment slot of lower pole section (3) in 23. Attach upper elevator tubes (40) to backboard support a lower hole of middle pole section (2) as in step 3. While brackets (29) using spacers (32), bolt (36), and nut (38) as shown. maintaining alignment, bounce assembly and lower section (3) 24. Support pole on sawhorse. Attach backboard assembly to top pole together as shown until they no longer move toward taped reference section (1). Install pole cap (41). mark. NOTE: Pole sections should have a 3-1/2” (9 cm) minimum IMPORTANT! Two people recommended for this step. overlap. Use caution; elevator assembly is heavy. 5. Install rod (7) through holes in bottom pole section (3) and 25. Install handle assembly to lower elevator tubes (35) using eyebolt (8). bolt (36), spacers (37) and nut (38). NOTE: Before go...