Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
CAUTION! 2 3 1 Bottom Pole IDENTIFICATION STICKER Bottom PoleIDENTIFICATION STICKER 5" 1-1/2" Holes in top (1) and bottom (3) pole sections MUST align to correctly position elevator system toward playing surface. IMPORTANT! POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: P/N M601111 08/05 10 SECTION B: ASSEMBLE THE BASE SECTION B: ASSEMBLE THE BASE TOOLS REQUIRED FOR THIS SECTION This is what your system will look like when you’ve finished this section: (2) 1/2”Wrenches (2) Socket Wrenches and Sockets AND/OR AND 1/2” Hammer or Mallet 11 08/05 P/N M601111 P/N M601111 08/05 12 11 15 10 2. Attach pole assembly to base using carriage bolts (15) washers(10) and nuts (11) as shown. Two people are required for this step. 1. Assemble pole bracket (12) using bolt (13) and Lock Nut (14) as shown. 13 12 14 DO NOT OVER TIGHTEN IMPORTANT! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! THE CUT CORNERS OF THE POLE BRACKET NEED TO FACE TOWARD THE BACK OF THE BASE AS SHOWN. IMPORTANT! 13 08/05 P/N M601111 3. Rotate non-secured ends of tank struts (16) outward to mounting holes in tank as shown.Secure ends of tank struts (16) to tank as shown. Repeat for opposite side. Secure tank struts (16) to pole as shown. Nut should be tightened until flush (even) with lock nuts outer edge. Place cap (17) over exposed end of bolt as shown. 9 10 11 10 10 10 14 17 13 16 16 16 4. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! P/N M601111 08/05 14 5. 6. Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet 4 6 6 7 7 5 Install wheel assembly to base (8) using bolts(9), washers(10) and nuts (11) as shown. 10 9 11 10 8 SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORTANT! CAREFULLY TIPPING THE SYSTEM ON IT'S SIDE WILL ALLOW EASIER ACCESS TO THE UNDERSIDE OF BASE. NOTE: 15 08/05 P/N M601111 TOOLS REQUIRED FOR THIS SECTION SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD This is what your system will look like when you’ve finished this section: 3/8” 1/2” 9/16” 3/4” (1) 3/8”, (2) 1/2”, (2) 9/16” and (2) 3/4” Wrenches Phillips Screwdriver (2) Socket Wrenches and Sockets AND/OR P/N M601111 08/05 16 1. Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolts (22) as shown. Tighten flange nuts (11) completely. 1 28 11 11 18 22 22 2. Attach spacers (24, 43) to pole mount bracket (28) with bolts (29), washers (50), and lock nuts (31) as shown. 28 50 50 31 29 50 50 43 24 24 43 IMPORTANT! Tighten just until washers (50) stop moving. 17 08/05 P/N M601111 3. 28 11 27 35 35 26 19 FIG. A Apply logo and height indicator labels (23) to adjustment rod (58) as shown. Attach handle parts (59, 60) to adjustment rod with screw (55), carriage bolts (54), and flange nuts (11) as shown. 4. 54 11 11 60 59 55 54 58 23 23 Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto pole mount bracket (28) with carriage bolt (19) and nut (11) as shown. IMPORTANT! Loop end of pin lanyard (26) over carriage bolt (19) as it passes through the pole mount bracket (28) during this assembly. 26 19 27 IMPORTANT! Indicator labels should be applied as close to holes as possible to prevent labels from being damaged during height adjustment. P/N M601111 08/05 18 29 30 30 29 52 Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (27). 27 5. 6. Assemble backboard brackets (52) 52 using bolts (29), and nuts (30) as shown. 7. A 7. A Assemble board pad to board. Work from the center - out. Using the holes which line up for your board size, attach center pad (48), right pad (45) and left pad (44) sections to board using screws (46) and washers (47) as shown. 44 46 46 47 48 45 47 IMPORTANT! DO NOT TIGHTEN HARDWARE COMPLETELY. BOARD STYLE MAY VARY B Secure left (44) and right (45) pad sections to and washers (47) as shown. 08/05 P/N M60111119 46 46 47 board by pushing pads over the corners of the board. Secure completely by using screws (46) 47 46 47 4647 44 45 48 IMPORTANT! TIGHTEN ALL HARDWARE COMPLETELY. BOARD STYLE MAY VARY 8. 8. Identify elevator tubes (33 & 34). Toward Toward 33Upper Elevator tube Toward PoleBoard 34Lower Elevator tube Toward PoleBoard Attach lower elevator tubes (34) and counter balance spring (36) to backboard support brackets (52) using spacers (53 & 56), bolt (57), and nut (21) as shown. 57 36 56 52 21 34 34 53 56 36 68 52 66 52 P/N M601111 08/05 20 9. 9. Attach upper elevator tubes (33) to backboard support brackets (52) using spacers (53), bolt (57), and nut (21) as shown. Tighten ALL Hardware from Steps 6-8 After this Assembly is Completed. IMPORTANT! 33 56 52 2153 57 33 56 57 56 56 2153 33 33 21 08/05 P/N M601111 21 21 49 25 34 1 32 32 57 20...