Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
5 4 6 TOP MIDDLE BOTTOM alignment mark alignment mark alignment mark Align poles using alignment marks. First, pound top and middle poles together by bouncing them on a scrap piece of wood on the ground as shown in FIG B. until they no longer move toward pole identification stickers. THEN add bottom pole section and pound together in the same way. middle pole IDENTIFICATION STICKER middle pole IDENTIFICATION STICKER 5" 1-1/2" THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 11/ 2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! FIG B. scrap wood (Not Supplied) Toll-Free Customer Service Number for U.S. : 1-800-558-5234 P/N 21173402 12/28/04 8 Toll-Free Customer Service Number for U.S. : 1-800-558-5234 9 12/28/04 P/N 21173402 Attach wheel carriage assembly to base (1) with bolt (13), washer (22), and nut (7) as shown. FINGER TIGHTEN - NO TOOLS REQUIRED. Assembly will be fully tightened in next step. 3. 4. 9 3 2 10 1 13 7 22 Install wheel axle (2) through wheel bracket (9) and install wheels (3) onto wheel axle (2) with spacers (10) as shown. THE SPACER (10) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. IMPORTANT!: BE SURE THAT THE SQUARE PORTION OF THE CARRIAGE BOLT IS PROPERLY SEATED IN THE SQUARE CUT-OUT OF THE WHEEL BRACKET. IMPORTANT!: Attach pole assembly to tank assembly as shown. Secure pole assembly to 5. tank and wheel bracket by turning the pole assembly clockwise as shown. Tighten pole completely and further rotate pole until struts are aligned correctly as shown in FIG B. FIG B TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT!: The pole should be turned approximately 7 complete rotations to tighten properly. When properly tightened, the wheel bracket will be tight against the base. An assistant is recommended to hold the base in place during this step. Toll-Free Customer Service Number for U.S. : 1-800-558-5234 P/N 21173402 12/28/04 10 6. 6. Rotate struts down and bend struts outward to line up with holes on base as shown. Secure free ends of tank struts to tank with carriage bolt (16), washer (22), and knob (17) as shown. Repeat for other side. KNOBS MUST BE TIGHTENED COMPLETELY AND CHECKED PERIODICALLY FOR TIGHTNESS. WARNING! 22 16 17 Toll-Free Customer Service Number for U.S. : 1-800-558-5234 11 12/28/04 P/N 21173402 Mount brackets (20 & 26) to backboard and finger tighten as shown.7. NOTE: Final adjustments will be made in Step 10. 20 32 24 25 26 27 26 27 Toll-Free Customer Service Number for U.S. : 1-800-558-5234 P/N 21173402 12/28/04 12 Toll-Free Customer Service Number for U.S. : 1-800-558-5234 13 12/28/04 P/N 21173402 28 30 31 26 27 Install Slam Jam Rim to Backboard 18 29 27 31 30 A B C D E A • Fit rim (18) securely into bracket (26) as shown (Allow "T"-bolt (27) to slip through center hole in rim (18). B • Install reinforcement bracket (28) onto “T” bolt (27) as shown. C • Install spring (29) onto “T” bolt (27) as shown. D • Install special nut (30) and washer (31) onto “T” bolt (27). E • Tighten nut (30) until flush with end of “T” bolt (27). 27 27 8. #28 SAWHORSE OR SUPPORT TABLE 9. Support pole and tank assembly over support table. Carefully slide backboard components onto pole. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. WARNING! While still in the horizontal position, carefully slide backboard components onto pole. Secure hardware at desired position as shown and tighten all hardware completely at this time. 12 23 17 10. Peel protective film from surface of acrylic backboard prior to use. NOTE: Toll-Free Customer Service Number for U.S. : 1-800-558-5234 P/N 21173402 12/28/04 14 Place assembled unit in desired location. Fill tank with water (26 gallons/98.4 liters) or sand (approx. 360 lb./163 kg) and snap tank cap (14) in place. Insert T-strap (11) through slot on back of base as shown. Secure unit to ground by 11. twisting tie down stake (21) into ground and hooking T-strap (11) onto tie down stake (21). CAUTION! ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUBFREEZING CLIMATES. 11 14 11 21 21 11 Toll-Free Customer Service Number for U.S. : 1-800-558-5234 15 12/28/04 P/N 21173402 Attach net clips to rim as shown. 12. CLIP “ARM” CLIP “BODY” 19USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECT...