Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Fotos und technische Daten Vision Fitness X6700HRT |
Anleitung Zusammenfassung
ORANGE BAG M8x20L Socket Head Bolt Quantity: 4 8.2x18x1.5T Arc Washer Quantity: 4 HARDWARE INCLUDED BLACK BAG Plastic Connector Quantity: 8 YELLOW BAG Spacer Quantity: 4 M8x55L Socket Head Bolt Quantity: 2 8x16x1T Washer Quantity: 2 M8 Nylon Nut Quantity: 2 M5x15L Bolt Quantity: 8 M8x25L Socket Head Bolt Quantity: 8 M8 Lock Washer Quantity: 8 M8x20L Panhead Bolt Quantity: 4 PINK BAG M8x25L Socket Head Bolt Quantity: 4 M8 Lock Washer Quantity: 4 BLUE BAG M10x55L Socket Head Bolt Quantity: 2 M10 Nylon Nut Quantity: 2 M5x12L Bolt Quantity: 2 10x24.5x1T Washer Quantity: 4 8x16x2T Washer Quantity: 4 M10 Lock Washer Quantity: 4 M10x25L Socket Head Bolt Quantity: 4 GREEN BAG M8x12L Bolt Quantity: 2 End Cap illustration not to scale Quantity: 226x36x2T Wave Washer Quantity: 4 26x36x0.3T Wave Washer Quantity: 2 25.5x38x1T Washer Quantity: 2 STEP 4 • Remove protective covers from sleeves of the pedal arms. IMPORTANT: The washers in the following step must be assembled in the correct order. • Slide one thin metal wave washer (26x36x0.3T), one flat washer (25.5x38x1T), and one plastic wave washer (26x36x2T) onto the axle of the right link arm. Slide the axle of the right link arm through the sleeve on the right pedal arm. Secure the link arm onto the pedal arm with the plastic wave washer (26x36x2T), end cap, and bolt (M8x12L). Tighten with the 5mm L-shaped wrench. • Repeat the step on the left side. GREEN BAG STEP 5 NOTE: With this next step it is helpful to have a second person to hold the dual-action arms in place while you assemble them. • Take the right dual-action arm and center the holes in the rotation housing on the console mast. Secure with four socket head bolts (M8x25L) and four lock washers (M8). Tighten with the 6mm T-shaped wrench. • Slide a spacer onto each side of the socket joint located on the end of the link arm. Slide the bottom of the dualaction arm bracket over the link arm socket and spacers. From the outside of the bracket, slide the bolt (M8x55L) through the hole in the bracket and socket joint. Secure with a washer (8x16x1T) and nylon nut (M8). Tighten with the 6mm T-shaped wrench and 13mm wrench. • Attach the inside dual-action arm cover onto the bottom of the dualaction arm with a bolt (M5x15L). Insert the plastic connector to the inside dual-action arm cover. Slide the outside dual-action arm cover onto the other end of the plastic connector. Secure the outside dual-action arm cover to the bottom of the dual-action arm with a bolt (M5x15L). Tighten both bolts with the screwdriver. • Repeat these steps on the left side. BLACK BAG STEP 3 STEP 6 • Slide the accessory tray onto the console mast. Secure in place with four panhead bolts (M8x20L). Tighten with the 5mm L-shaped wrench. • Remove the four bolts (M5x12L) from the back side of the console. Connect the wire harness and the heart rate wires to the plugs in the back side of the console. Place the console on the mast and secure in place with the bolts (M5x12L). YELLOW BAG STEP 4 STEP 6 STEP 5 Console Mast Boot Mounting Plate Console Mast Frame Bracket Link Arm Pedal Arm Rotation Housing Dual-Action Arm Console Accessory Tray STEP 3 • Slide the console mast boot onto the console mast. • Attach the mounting plate to the bottom of the console mast with four socket head bolts (M10x25L) and four lock washers (M10). Tighten as much as possible with the 8mm L-shaped wrench. • Mount the console mast on the frame by sliding the guide hole on the mast mounting plate over the guide screw on the front of the frame bracket. Place a lock washer (M8) followed by a flat washer (8x16x2T) on each of the four remaining socket head bolts (M8x25L). Insert the bolts to the rear holes but do not completely tighten. Next, insert the bolts to the front holes. Tighten all four bolts as much as possible with the 6mm L-shaped wrench. • Wrap the wire tie that exits the hole at the bottom front side of the console mast around the wire harness coming up from the frame. Pull the wire tie and wire harness up through the top of the console mast. • Insert a zip tie through the hole in the middle of the console plate and loop it around the heart rate wires and wire harness. Pull to snug, but do not over tighten. PINK BAG STEP 2 STEP2 • Take the right pedal arm and set the roller wheel in the aluminum guide track. Slide the opposite end of the pedal arm into the U-shaped knuckle bracket. Slide a socket head bolt (M10x55L) with a washer (10x24.5x1T) through the hole in the knuckle bracket and pedal arm. Fix in place with a washer (10x24.5x1T) and nylon nut (M10). Tighten with the 8mm L-shaped wrench and the 17mm wrench. • Slide the pedal arm cover over the knuckle joint and fix in place with a bolt (M5x12L). Tighten with the screwdriver. • Repeat these steps on the left side. BLUE BAG STEP 1 • Place a piece of packaging under the front of the unit to aid in assembly of the front foot. • Secure the front stabilizer tube to the base frame plate with four socket head bolts (M8x2...