Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Be sure to read your Owner’s Guide before using your new Fitness Cycle. If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12 NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Cycle to prevent loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely tightening any ONE screw. 1STEP2STEP3STEP4STEP TOOLS & PARTS INCLUDED 15mm Pedal Wrench 5mm Allen Wrench Screwdriver 5mm L-Shaped Wrench 4mm L-Shaped Wrench 6mm L-Shaped Wrench PARTS BOX Console Mast Cover, Qty: 1 Pedals, Qty: 2 Power Supply, Qty: 1 Water Bottle & Cage, Qty: 1 Heart Rate Chest Strap (R2200HRT Only) Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card HARDWARE INCLUDED ORANGE BAG BLUE BAG PINK BAG M8 x 20L Screws Quantity: 2 M8 x 65L Screw Quantity: 2 M8 Lockwashers Quantity: 4 M8 x 20L Socket-head Cap Screw Quantity: 4 M8 x 15L Screws Quantity: 4 M8 Lockwashers Quantity: 4 M6 Lockwashers Quantity: 8 M6 x 55L Screws Quantity: 8 M8 x 15L Screws Quantity: 5 M8 x 20L Screws Quantity: 2 M8 Lockwashers Quantity: 6 5 STEP 1 STEP 1 • Slide the rear foot into place on the frame. Secure the foot in place with two screws (M8x20) and two lock washers (M8) to the outside holes and with two screws (M8x65) and two lock washers (M8) to the inside holes. Tighten with the blue-handled 5mm allen wrench. • Slide the rubber sleeve, located on the rear support tube, into place over the rear foot. ORANGE BAG Rear Foot 6 Seat Frame B A Seat Bracket R2200HRT Seat Lever R2200 STEP 2 STEP 2 • Place the seat bracket on the seat frame. Secure in place with four (M8x20) socket-head cap screws. Tighten with the 6mm L-shaped wrench. • Remove the socket-head cap screw in front of the seat lever, located on the right side of the seat frame, with the 4mm L-shaped wrench. Line-up the seat lever into position on the bracket. Reinsert the socket-head cap screw and tighten with the 4mm L-shaped wrench. • Take the seat frame handlebar and connect the heart rate wires (A) exiting its center to the heart rate wires (B) coming from the seat frame. • Mount the seat handlebars to the seat frame with four screws (M8x15L) and four lock washers (M8). Tighten with the 5mm allen wrench. • Mount the seat backrest cushion to the seat frame with four screws (M6x55L) and four lock washers (M6). Tighten with the 4mm L-shaped wrench. • Mount the seat bottom cushion to the seat frame with four screws (M6x55L) and four lock washers (M6). Tighten with the 4mm L-shaped wrench. R2200HRT ONLY: Snap the plastic cover onto the rear of the seat back. BLUE BAG 7 STEP 3 STEP 3 • Slide the console mast cover onto the console mast. • Use the wire tie coming from the bottom of the console mast to wrap around the wire harness and heart rate wires that are sitting in the frame bracket. • Pull the wire tie up through the console mast so the wire harness and heart rate wires exit the top of the mast. • Slide the bottom of the console mast into the frame bracket. Use the 5mm allen wrench to secure the four screws (M8x15) and four lock washers (M8) to the sides of the console mast bracket. Use the 5mm L-shaped wrench to secure the last screw (M8x15) to the edge of the bracket facing the seat. Tighten only until snug. • Mount the console mast handlebar to the console mast with two screws (M8X20) and two lock washers (M8). Tighten with the 5mm allen wrench. • With a screwdriver remove the four mounting screws from the backside of the console. Connect the heart rate wires and the wire harness to the pin connectors on the backside of the console. Mount the console to the console mast using the four mounting screws and the screwdriver. • Slide the console mast cover into place so it integrates with the side covers. • Mount the water bottle cage to the console mast with the screws located on the console mast. PINK BAG Console Mast Handlebar Console Console Mast Console Mast Cover R2200 8 500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551 toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373 ©2005 Vision Fitness. All Rights Reserved. 1.05 Part #Z22RB42D-AG AG18.16PRD REV4 STEP 4 STEP 4 • Attach left pedal strap to left pedal and right pedal strap to right pedal. • Attach right pedal to right crank arm and left pedal to left crank arm. Tighten with the 15mm pedal wrench. PEDALS ...