Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
12. A spotter is recommended during exercise. 13. Maximum user’s weight capacity 200 lbs. 14. Maximum weight capacity on Leg Developer 80 lbs. 15. Maximum weight capacity on Uprights 200 lbs. CARE AND MAINTENANCE 1. Inspect and tighten all parts before using the machine. 2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT use solvents. WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown. 3 HARDWARE PACK 4 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Left & Right Upright Beams (#1 & 2) onto the Lower Upright Beams (#3). B.) Connect the Left & Right Upright Beams by a Cross Brace (#4) in the Mid-span. Secure them with two M8 x 2 1/8” Hex Bolts (#18), one Bracket (#16), four . 5/8” Washers (#24), and two M8 Aircraft Nuts (#26) on each end of the Cross Brace. C.) Place the Backrest Adjustment Bar (#13) onto selected slot on the Upright Beams to obtain desired incline of Backrest. DIAGRAM 1 5 STEP 2 (See Diagram 2) A.) Insert the Main Support Frame (#5) into the Seat Support Frame (#6). Secure them with two M8 x 2 1/8” Hex Bolts (#18), two Brackets (#16), four O 5/8” Washers (#24), and two M8 Aircraft Nuts (#26). B.) Attach the Main Support Frame (#5) to the Cross Brace (#4). Secure it with two M8 X 2 1/8” Hex Bolts (#18), one Bracket (#16), four O 5/8” Washers (#24), and two M8 Aircraft Nuts (#26). C.) Attach the Seat Support Frame (#6) to the Leg Developer Holder (#7). Secure it with two M8 x 2 1/8” Hex Bolts (#18), one Bracket (#16), four O 5/8” Washers (#24), and two M8 Aircraft Nuts (#26). D.) Place the Seat Pad (#12) onto the Seat Support Frame (#6). Secure it with two M6 x 5/8” Hex Bolts (#21) and two O .” Washers (#25). DIAGRAM 2 6 STEP 3 (See Diagram 3) A.) Insert the two Upper Backrest Supports (#8) into two Lower Backrest Supports (#9). Secure them with two M6 x 1 3/8” Hex Bolts (#20), four O .” Washers (#25), and two M6 Aircraft Nuts (#28). B.) Attach the side-holes on the Lower Backrest Supports (#9) to each end of the pivot on the Seat Support Frame (#6). Align the holes and insert a M10 x 6 7/8” Axle (#17) through the holes. Secure it with two O .” Washers (#23) and M10 Aircraft Nuts (#27). Do not over tighten the Nuts. Make sure the Backrest Supports are able to swivel. C.) Place the Lower Backrest Board (#10) onto the Backrest Supports. Secure it with four M6 x 1 3/8” Hex Bolts (#20) and O .” Washers (#25). D.) Place the Upper Backrest Board (#11) onto the Backrest Supports. Secure it with two M6 x 1 3/8” Hex Bolts (#20) and O .” Washers (#25). DIAGRAM 3 7 STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#29) to the Leg Developer Holder (#7). Secure it with one M10 x 2 1/8” Hex Bolt (#19), two O .” Washers (#23), and one M10 Aircraft Nut (#27). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able to swivel. B.) Insert the Weight Post (#31) into the Leg Developer. Secure it with one M8 x 1 .” Hex Bolt (#22), two O 5/8” Washers (#24), and one M8 Aircraft Nut (#26). C.) Insert the Foam Tube (#30) halfway through the holes on the Leg Developer. Attach two Foam Rolls (#32) onto the Tube from both ends. DIAGRAM 4 8 9 PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 2 3 4 6 7 8 9 11 12 13 14 16 17 18 19 21 22 23 24 26 27 28 29 31 32 33 34 36 Left Upright Beam 1 Right Upright Beam 1 Lower Upright Beam 2 Cross Brace 1 Main Support Frame 1 Seat Support Frame 1 Leg Developer Holder 1 Upper Backrest Support 2 Lower Backrest Support 2 Lower Backrest Board 1 Upper Backrest Board 1 Seat Pad 1 Backrest Adjustment Bar 1 1 .” Square End Cap 1 1” Square End Cap 4 Bracket 6 M10 x 6 7/8” Axle 1 M8 x 2 1/8” Hex Bolt 10 M10 x 2 1/8” Hex Bolt 1 M6 x 1 3/8” Hex Bolt 8 M6 x 5/8” Hex Bolt 2 M8 x 1 .” Hex Bolt 1 O .” Washer 4 O 5/8” Washer 22 O .” Washer 12 M8 Aircraft Nut 11 M10 Aircraft Nut 3 M6 Aircraft Nut 2 Leg Developer 1 Foam Tube 1 Weight Post 1 Foam Roll 2 O 1” End Cap 1 O .” End Cap 2 1 .” Square End Cap 2 Rubber Bumper 1 10 IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation und...