Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: Impex Dateigröße: 490.12 kb Dateiname: 99020193.pdf Unterrichtssprache:

Slide a Weld Cover (63) onto each of the indicated axles on the Front and Rear Uprights (7, 2). The Weld Covers must be turned so the open sides are facing the Uprights. Lubricate the axles. Slide a Long Riser (3) onto the axles. The Long Riser must be turned as shown. Hold a 3/4" Retainer (57) and a 3/4" Retainer Cap (59) against the end of one of the axles. The teeth on the Retainer must bend toward the Retainer Cap (see the inset drawing). Tap the Retainer and Retainer Cap onto the axle. Tap a 3/4" Retainer (57) and a 3/4" Retainer Cap (59) onto the other axle. Attach the other Long Riser (3) to the lower axles on the other side of the Front and Rear Uprights (7, 2) in the same manner. 85 53 4 19 41 57 59 7 Axle Teeth cate 5 . 7o Slide a Weld Cover (63) onto each of the indicated axles on the Front and Rear Uprights (7, 2). The Weld Covers must be tumed so the open sides are facing the Uprights. Lubricate the axles. Slide a Short Riser (4) onto the axles, The Short Riser must be turned as shown. Hold a 3/4" J=tetainer (57) and a 3/4" Retainer Cap (59) against the end of one of the axles. The teeth on the Retainer must bend toward the Retainer Cap (see the inset drawing). Tap the Retainer and Retainer Cap onto the axle. Tap a 3/4" Retainer (57) and a 3/4" Retainer Cap (59) onto the other axle. Attach the other Short Riser (4) to the upper axles on the other side of the Front and Rear Uprights (7, 2) in the same manner. Pull back the Knob (39) on the Selector (20, 26). Raise the Selector Plate (19) to the position shown, with the Selector Plate between the sides of the Selector. Release the Knob, making sure that it is engaged in one of the holes in the Selector Plate. Hold the 3/4" x 1/2" Spacer (64) between the small holes in the lower end of the Selector (20, 26). Attach the Spacer with a 1/4" x 1 1/4" Bolt (49) and a 1/4" Nylon Jam Nut (55). 2 Lubricate 57 59 Axle Teeth 6 . Carefully cut the wire tie attached to the Cable (25). Wrap the loop of Cable from steps 4 and 5 around the 3 1/2" Pulley (27) as shown. Hold the Pulley and the Pulley Covers (88) between the indicated holes in the Selector Plate (19). Make sure that the Pulley Covers are turned so the small rims are inside the loop of Cable as shown. See assembly step 9, and make sure that the Cable is routed exactly as shown. Attach the Pulley Covers (88) and the 3 1/2" Pulley (27) to the Selector Plate (19) with the 3/8" x 2" Bolt (87) and a 3/8" Nylon Jam Nut (41). Rims Note: This section of cable must go over the top of the indicated pulley Wire Tie exactly as shownl The drawing at the right shows the correct route of 9 the Cable (25). Make sure that the Cable is routed exactly as shown. Note: The letters indicate the order in which the Cable is muted around the Pulleys. 25 B D G E 7 10.PulltheMomentArm(10)forward. Hold the lower and of the Left Press Arm (52) in the upper end of the Moment Arm. The Left Press Arm must be turned so the Handle (12) is on the side shown. Attach the Lef...

Herunterladen

Geben Sie zwei Ziffern: