Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 3 ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Adjustable Wrench and Allen Wrench NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach the Rear Stabilizer (#33) and the Base Frame (#45) to the Main Stabilizer (#35). Secure them with two M12 x 4” Carriage Bolts (#38), . 1” Washers (#12) and M12 Aircraft Nuts (#13). B.) Attach the Rear Vertical Beam (#19) to the Rear Stabilizer (#33). Secure it with two M12 x 1” Allen Bolts (#29) and . 1” Washers (#12). C.) Attach the Front Vertical Beam (#22) to the Base Frame (#45). Secure it with two M12 x 4” Carriage Bolts (#38), . 1” Washers (#12), and M12 Aircrafts (#13). D.) Attach the Seat Frame (#53) to the Base Frame (#45). Secure it with three M12 x 1’ Allen Bolts (#29) and . 1” Washers (#12). 4 STEP 2 (See Diagram 2) A.) Align the rear of Upper Frame (#8) to the Rear Vertical Beam (#19). Attach the Top Socket Assembly (#14) to the joint. Secure it with four M12 x 3 1/8” Carriage Bolts (#11), .1” Washers (#12), and M12 Aircraft Nuts (#13). Do not tighten the bolts yet. B.) Place the Upper Frame onto the open bracket on the Front Vertical Beam (#22). Secure it with one M10 x 3” Allen Bolt (#44), two . .” Washers (#43), and one M10 Aircraft Nut (#5). Securely tighten all bolts previously installed. C.) Attach the Foot Plate Support (#40) to the Base Frame (#45). Secure it with two M12 x 1” Allen Bolts (#29) and . 1” Washers (#12). D.) Attach the Foot Plate (#41) to the Foot Plate Support (#40). Secure it four M10 x 1” Allen Bolts (#42), . .” Washers (#43), and M10 Aircraft Nuts (#5). 5 STEP 3 (See Diagram 3) A.) Insert the two Guide Rods (#18) into the holes on the Main Stabilizer (#35). Slide two Rubber Washers (#26) onto the Guide Rods from the top. NOTE: WD-40 or similar lubricant might be needed to reduce friction. B.) Slide two Guide Rod Sleeves (#28) and two Rubber Bumpers (#27) onto the Guide Rods (#18). Then slide the Weight Holder (#24) onto the two Guide Rods. At last, slide two Guide Rod Rings (#15) onto the Guide Rods. C.) Align the Guide Rods to the holes on the Top Socket Assembly (#14). Lift up the Rings (#15) to secure the Rods with two M8 x .” Allen Bolts (#16). D.) Slide a Rubber Washer (#26) and Olympic Sleeve (#30) onto the post on the Weight Holder (#24). Secure the Olympic Sleeve with a M8 x .” Allen Bolt (#16). Plug an Olympic Sleeve End Cap (#34) to the end. Clip a Spring Clip (#32) onto the Sleeve. Repeat the same procedure for the other side. E.) Attach the Arm Curl Pad (#55) to the Arm Curl Stand (#54). Secure it with two M8 x 1 3/8” Allen Bolts (#49) and . 5/8” Washers (#50). Insert the Stand into the top opening on the Seat Frame (#53). Use the Lock Knob (#46) to select desired height for the Arm Curl Pad. F.) Insert the Seat Adjustment Frame (#47) into the front opening on the Seat Frame (#53). Use a Lock Knob (#46) to select the desired position. G.)Attach the Seat Pad (#51) to the Seat Post (#52). Secure it with two M8 x 1 3/8” Allen Bolts (#49) and . 5/8” Washers (#50). Insert the Seat Post into the Seat Adjustment Frame (#47). Use the Lock Knob to select desired height for the Seat. 6 DIAGRAM 3 7 STEP 4 (See Cable Loop & Diagram 4) A.) Attach the 119” Upper Cable (#10) to the front opening on the Upper Frame (#8). Make sure the ball stopper on the Cable is under the opening. B.) Attach a Pulley (#9) to the opening. Secure it with one M10 x 2 .” Allen Bolt (#7), two Bushings (#6), and one M10 Aircraft Nut (#5). C.) Draw the Cable towards the back of the machine to the second opening on the Upper Frame. Repeat Step B above to install a Pulley. D.) Draw the Cable downward. Place a Pulley in between the two Pulley Brackets (#21). Secure them together with one M10 x 2” Allen Bolt (#17), two . .” Washers (#43), and one M10 Aircraft Nut (#5). Draw the Cable around the Pulley and the Bracket hanging for now. E.) Pull the Cable upward towards the open bracket on the Top Socket Assembly and install a Pulley to the bracket. F.) Pull the Cable downward to the opening hole on top of the Weight Holder. Thread the tip of the Cable into the hole to firmly secure the Cable. G.)Attach the 104” Lower Cable (#23) to the upper opening on the Front Vertical Beam (#22) and install a Pulley. Make sure the ball stopper is in the front of the Beam. Draw the Cable underneath the Pulley then pull up to the hanging Pulley Bracket previously installed. H.) Install a Pulley to the lower opening on the hanging Bracket. Note: There are a few holes on the Bracket. Use these holes to adjust the tightness of the Cables by selecting different holes. Draw the Cable over the Pulley then downward to the open bracket on the Front Vertical Beam. I.) Install a Pulle...