Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Wait five minutes and then press the switch back in. 4 Check the house electrical breaker box and the circuit breaker for the room where the treadmill is located. If it has tripped, reset or have an electrician replace the breaker in home. 5 Have an electrician check for inadequate voltage at the outlet. Treadmill loses power during use. 1 Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in. 2 Check the house electrical breaker box and the circuit breaker for the room where the treadmill is located. If it has tripped, reset or have an electrician replace the breaker in home. 3 If the treadmill still will not operate, please call IRONMANS Technical Service at (888) 340-0482. Treadmill walking belt slows during use. 1 Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less and the surge protector is securely plugged into the outlet. 2 If treadmill still will not operate, please call IRONMANS Technical Service at (888) 340-0482. Treadmill walking belt slips or is not centered on rear roller. 1 Refer to “Belt Adjustment and Tension” section on page 15. 2 Need help? Call IRONMANS Technical Service at (888) 340-0482. Treadmill Error Messages. Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not operate the treadmill until the problem is corrected. Call IRONMANS Technical Service at (888) 340-0482. Or see page 19 of this Owners Manual. 19 Error Messages Treadmill Error Messages. Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. The following error codes will be displayed in the console display windows. Safety Interlock Error Messages SI 1 - Safety key missing, replace and try again. SI 2 - Over voltage protection trip. Notify Ironman Fitness Technical Service. SI 3 - Tilt Switch Trip. Notify Ironman Fitness Technical Service. Other Error Messages E11 -Lack of speed feedback data from belt motor. Attempt re-calibration. See Calibration Sequence section on page 20 of this Owners Manual for detailed information. E22 - Under Speed condition detected from the belt motor. Attempt re-calibration. See Calibration Sequence section for detailed information. E33 - Over Speed condition detected from the belt motor. Attempt re-calibration. See Calibration Sequence section for detailed information. To avoid possible damage to the treadmill and the possibility of injury, do not operate the treadmill until the problem is corrected. Call Ironmans Technical Service at (888) 340-0482. Calibration Sequence 20 Our treadmill is equipped with a software package that will perform a calibration sequence unique to your specific model number. Please perform the following steps to calibrate the IRONMAN M6 TREADMILL. 1. Unplug power cord from outlet strip. 2. Attach Safety Key to console. 3. Plug power cord into outlet strip. 4. Initiate calibration sequence. Locate hole on the back of the console and insert the eraser end of a pencil through the hole and press the calibration switch twice. As show on page 14. 5. CL21 should appear in the Time window, if not, continue to press the calibration switch until CL21 appears. Note: During the calibration sequence, the Time window will display which step you are at in the process (C21, C22, C23 and so on). The CAL/DIST window will display which key should be entered next. For example, “E” for Enter, “P” for Power, or “SS” for Start / Stop. 6. CL21: MPH or KPH will be flashing in the Speed window, pressing the Speed +/ - button will toggle options. Choose MPH (KPH), press Enter. 7. CL22: 8, 10, or 12 (13, 16, or 20 in KPH mode) will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose 10 (or 16 for KPH mode), press Enter. 8. CL23: FFF, UUU, or HHH will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose UUU, press Enter. 9. CL24: 111 or 222 will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose 222, press Enter. 10. CL25: AL1 or AL2 will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose AL1, press Enter. 11. CL26: OPA or OPI will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose OPA, press Enter. 12. CL27: Blank (nothing), “a”, “b”, “c”, or “d” will be displayed in the Incline window, pressing the Speed +/ - button will toggle options. Choose Blank, press Enter. 13. CAL/DIST window will display “E”, Press Enter. “55” will display in CAL/DIST window. 14. Press Start/ Stop. 15. At this time, make sure you are not standing on the walking belt, as the machine will automatically initiate belt ...