Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch three times. TOE TOUCH STRETCH Stand, bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, back of knees, and back. HAMSTRING STRETCH Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, lower back, and groin. CALF/ACHILLES STRETCH With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. To cause further stretching of the Achilles tendon, bend your back leg as well. This will stretch your calves, Achilles tendons, and ankles. QUADRICEPS STRETCH With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles. INNER THIGH STRETCH (Image not Shown) Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles. 30 Change to MPH or KPH Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in kilometers, follow the steps described here: 1) Turn power OFF on the console. (Do not unplug treadmill.) Attach the magnet safety key to the console. 2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the console (see diagram below). 3) Depress the calibration mode switch ONCE. CL11 should appear in the TIME window. 4) Pressing the SPEED +/- button will activate your choice. 5) To accept the setting, press the POWER button. Note: The treadmill pictured below may not be identical to your particular model. 31 Calibration Sequence Do not attempt to calibrate the treadmill unless an Error Code is present. See Error Messages (page 35). Our treadmill is equipped with a software package that will perform a calibration sequence unique to your specific model number. Please perform the following steps to calibrate the Ironman LEGACY Treadmill. 1. Unplug power cord from outlet strip. 2. Attach Safety Key to console. 3. Plug power cord into outlet strip. 4. Initiate calibration sequence. Locate the hole on the back of the console and insert the eraser end of a pencil through the hole and press the calibration switch twice. As show on page 31. 5. CL21 should appear in the Time window, if not, continue to press the calibration switch until CL21 appears. Note: During the calibration sequence, the Time window will display which step you are at in the process (C21, C22, C23 and so on). The CAL/DIST window will display which key should be pressed next. For example, “E” for Enter, “P” for Power, or “SS” for Start / Stop. 6. CL21: MPH or KPH will be flashing in the Speed window, pressing the Speed +/ - button will toggle options. Choose MPH (KPH), press Enter. 7. CL22: 8, 10, or 12 (13, 16, or 20 in KPH mode) will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose 10 (or 16 for KPH mode), press Enter. 8. CL23: FFF, UUU, or HHH will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose UUU, press Enter. 9. CL24: 111 or 222 will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose 222, press Enter. 10. CL25: “---” will be displayed in the Speed window, press Enter. 11. CL26: OPA or OPI will be displayed in the Speed window, pressing the Speed +/ - button will toggle options. Choose OPA, press Enter. 12. CL27: Blank (nothing), “a”, “b”, “c”, “d” or “e” will be displayed in the Incline window, pressing the Speed +/ - button will toggle options. Choose “E”, press Enter. 13. CAL/DIST window will display “55”. Press Start / Stop. “E” will display in CAL/DIST window. 14. At this time, make sure you are not standing on the walking belt, as the machine will automatically initiate belt movement and run through a complete calibration and diagnostic routine. Press Enter. Belt...