Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Keys Fitness, modell DT1000 831.288261

Hersteller: Keys Fitness
Dateigröße: 538.88 kb
Dateiname: 83aa5054-99c3-43c0-bad2-af17eb44069f.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is 831.288261. The serial number can be found on a decal attached to the DT1000 (see the front cover of this manual for the location of the decal). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Pedal Side Shield Link Arm Adjustable Cap Electronic Monitor Water Bottle Holder (Bottle not included) Towel Holder Handlebar Seat Knob Seat Seat Post Frame 3 ASSEMBLY Assembly requires two people. Place all parts of the LIFESTYLER. DT1000 in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Read through all steps before beginning. During assembly, make sure that all parts are oriented as shown in the drawings. Assembly requires the included tool and grease packet, an adjustable wrench , a rubber mallet , and a phillips screwdriver 1. Insert the end of the Rear Stabilizer (34) into the Frame (46). Attach the Rear Stabilizer to the Frame with four M5 x 12mm Screws (56). 2. Turn the Front Stabilizer (20) so the indented holes are facing the floor. Attach the Front Stabilizer to the Frame (46) with two M8 x 48mm Carriage Bolts (57), two M8 Washers (43), and two Acorn Nuts (12). 3. Remove the three 8mm Locknuts (36) from the underside of the Seat (40). Attach the Seat to the top of the Seat Post (41) with the three Locknuts. Insert the Seat Post (41) into the Frame (46). Align one of the holes in the Seat Post with the hole in the Frame. Insert the Seat Knob (45) into the Frame and the Seat Post, and tighten the Seat Knob into the Frame. Make sure to insert the Seat Knob through one of the holes in the Seat Post; do not insert the Seat Knob under the Seat Post. 4. Apply a small amount of grease to the Pivot Shaft (17). Slide the Pivot Shaft into the Frame (46) and center it. Slide the Left Handlebar (10) onto the left end of the Pivot Shaft. Slide the Right Handlebar (not shown) onto the right end of the Pivot Shaft. Attach an M8 Washer (43) and an 8mm Locknut (36) to each end of the Pivot Shaft. 1 34 56 46 12 43 46 2 20 57 43 40 45 46 3 36 41 36 46 17 10 4 43 36 4 5. The Electronic Monitor (19) requires two OAAO batteries (not included). Alkaline batteries are recommended. Locate the battery compartment on the back of the Monitor. Insert two batteries into the Monitor. Make sure that the negative ends of the batteries (marked O.O) are touching the springs in the Monitor. Close the battery cover. 6. Thread the wire on the Electronic Monitor (19) through the hole in the middle of the Monitor Bracket (61). Attach the Electronic Monitor (19) to the Monitor Bracket with four Monitor Screws (59). Connect the Sensor Wire (47) to the wire on the Electronic Monitor (19). Attach the Monitor Bracket (61) to the Frame (46) using two M4 x 12.5mm Tek Screws (60). Make sure that the S...