Stimmen - 4, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
Install and tighten each 3 1/2” x 5/16” bolt (2) with washers from the bottom of the base frame through the upright lock (diag. 1). 2. Now tighten the buttonhead screws securely from step 1. 3. Tighten the black, flathead pivot bolts on the inside of upright. 4. Install motor hood cover using 5/8” phillips head screws (8 screws). Be sure the treadmill is level to the floor. The rear feet can be adjusted to level the treadmill. Assembly is now complete! Power Requirements IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill. Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps. This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing (1) below. 7 Console Functions and Descriptions PROGRAM BUTTONS - These buttons are used to access each of the three programs: Fat Burn, Cardio, and Warm Up. Each program has one preset program, and two additional custom programs in the P1 and P2 mode. See the “Program and Operating Instructions” on page 12. START/STOP - This button starts the treadmill belt moving. There is a 4 second countdown built in as a safety feature to let you know the treadmill belt is about to start moving. Use the START/STOP button also to stop your treadmill after your workout. The belt will gradually come to a stop after pressing the button. POWER - Press to on. Allow 6-8 seconds while the electronics perform a self check prior to pressing other SPEED - Use to either increase (UP arrow) or decrease (DOWN arrow) the speed. These buttons are also used while programming SPEED and TIME. ENTER - Use the Enter button while setting program time, speed, and incline options. See page 12 for complete CONSOLE SAFETY KEY - Place the RED Safety Key here prior to turning power on. THE TREADMILL WILL NOT OPERATE WITHOUT THE SAFETY KEY ATTACHED. The safety key is equipped with a string and clip that will clip to your clothing. This is an important safety feature that will automatically turn the power off if you should trip or fall while using the treadmill. INCLINE - Use to either increase (UP arrow) or decrease (DOWN arrow) the incline. These buttons are also used while programming INCLINE. ONE TOUCH INCLINE BAR - Use to either increase or decrease the incline. Each number indicates percent of grade. Pressing one of the buttons will gradually increase or decrease the incline to the ONE TOUCH SPEED BAR - Use to either increase or decrease the speed. Each number indicates MPH. Pressing one of the buttons will gradually increase or decrease the speed to the new setting. PAUSE - Press to temporarily pause your workout while in use. The treadmill is designed with an automatic power off feature after 5 minutes in the pause mode. 8 Console Functions and Descriptions There are five display windows on the control panel to provide feedback information. TIME WINDOW • TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) • INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0 seconds SPEED WINDOW • SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments DISTANCE / CALORIES WINDOW • DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0 • CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time 9 Console Functions and Descriptions INCLINE WINDOW • INCLINE: Indicates incline in percent of grade 0-12% in 1 increments • PULSE (880HR Model Only): Indicates current heart rate • HEART “¦” (880HR...
Dieses Handbuch ist für folgende Modelle:Kraftstationen - Alliance 880HR (638.14 kb)