Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Do not use this exercise bike with bare feet, sandals, socks or stockings! • Always examine your exercise bike before using to ensure all parts are in working order. • Do not leave children unsupervised near or on the exercise bicycle. • Never operate the exercise bicycle where oxygen is being administered or where aerosol products are being used. • Never insert any object or body parts into any opening. • Service to your Alliance Exercise Bike should only be performed by an authorized service representative, unless authorized and/or instructed by a Keys technician. Failure to follow these instructions will void the warranty. 3 Assembly of Alliance 920 Recumbent Bike Assembly of Alliance 920 Recumbent Bike REMOVE ALL SECURITY AND WRAPPING BEFORE BEGINNING. 1 1. Attach foot tubes (4) to the frame by using the carriage bolts (44), flat washers (50) and cap nuts ( 45) provided. Make sure the foot tube with wheels is assembled onto the front of the unit. 4 2a. Attach the rear handlebar the seat carriage (3) washers (50) and screws Connect the seat cushions (9,10) to the seat carriage (3) the washers (78) and screws (80). 2a 2b 2b. First remove the support tube (24), from the main frame (1). Slide the assembled seat carriage onto the carriage tube (16). Re-assemble the support tube (24). Attach the end cap (17) with screws (57) and rear carriage tube rubber stopers (66) with bolts (74, 75) and washer (76). 5 3 4 3. Attach pedals (30, 31). Axles of pedals are branded “L” and “R.” The pedal marked “R” goes on the right hand side of the bike and the one marked “L” on the left hand side. Tighten the left pedal by turning counter-clockwise and the right pedal by turning clockwise. 4. Slide the console tube (2) through the console tube collar (14). Connect the computer cable in the console tube (2) to the computer cable in the main frame. Attach the console tube (2) to the frame (1) with the locknuts (49), flat washers (50) and screws (56) provided. Attach the console tube collar (14) to the main frame (1) with screws (57). 6 7 6 5 5. Load your console with the batteries provided. Batteries are 4 “AA” size. 6. Connect the computer cable at the top of the console tube (2) to the console (5). Both computer cable connections have white ends. Feed the pulse wires from the console (5) down into the console tube (2) and out the rear hole in the handlebar area. Attach the console tube (2) to the console (5) with the screws (59) provided and already attached to back of the console (5). Attach bottle rack to console tube (2). 8 9 87 7. Attach the pulse wires in the front handlebar (23) to the wires from the console (5). Connect the front handlebar (23) to the console tube with the locknuts (49), flat washers (50) and screws (55) provided. Make sure not to “pinch” any of the pulse wires when connecting the handlebar to the console tube. 8. You have completed the assembly of your new Alliance bike. 10 11 920R PARTS LIST 920R EXPLODED VIEW 920R PARTS LIST 920R EXPLODED VIEW # PART 1 FRAME 2 CONSOLE TUBE 2-1 BOTTLE RACK 3 SEAT CARRIAGE 4 FOOT TUBE CONSOLE 6 PULLEY 7 GENERATOR 8 CONTROLLER BOARD 9 SEAT CUSHION BACK SEAT CUSHION 11 BOTTOM LEFT COVER 12 BOTTOM RIGHT COVER 13 TOP COVER 14 CONSOLE TUBE COLLAR CONNECTING COVER 16 CARRIAGE TUBE 17 END CAP 18 ADJUSTING PLATE 19 “V” BELT WHEEL 21 FOOT CAP 22 REAR HANDLEBAR 23 FRONT HANDLEBAR 24 SUPPORT TUBE HAND PULSE 26 PULSE WIRE 27 CONTROLLER EXT. WIRE 28 CONTROLLER WIRE 29 9mm NUT LEFT PEDAL 31 RIGHT PEDAL 32 LEFT CRANK 33 RI GHT CRANK 34 LOCKING KNOB 6004 PRECISE BEARING 36 608 PRECISE BEARING 37 EYEBOLT 38 SPRING 39 BELT TENSION BRACKET ADJUSTMENT CHANNEL 41 SENSOR 42 IDLER PULLEY 12 QTY 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 2 1 1 1 2 2 2 1 2 1 1 1 1 1 2 1 2 1 1 2 1 1 # PART QTY 43 CRANK CENTRAL CAP 2 44 M8X85mm CARRDIAGE BOLT 4 45 M8 CAP NUT 4 46 M6 LOCKNUT 4 47 6mm HEX NUT 2 48 M10 CAP NUT 2 49 M8 LOCKNUT 18 50 M8 IDX18.8mm FLAT WASHER 38 51 M20X32X2mm WASHER 2 52 CRANK NUT 2 53 M8X17mm SCREW 1 54 M8X38mm SCREW 1 55 M8X57mm SCREW 3 56 M8X60mm SCREW 3 57 TP4X12mm SCREW 30 58 TP5X50mm SCREW 4 59 M5X10mm SCREW 4 60 M6X45 MACHINE SCREW 4 61 REAR SLEEVE 2 62 REAR BALL PLUG 2 63 FRONT BALL PLUG 2 64 CAM LOCK 1 65 SEAT CARRIAGE BRACKET 1 66 RUBBER STOPPER 4 67 SMALL ROLLER 6 68 M8 WAVED WASHER 6 69 M13 WAVED WASHER 4 70 8*13mm BUSHING 4 71 RETAINING RING 2 72 8*34mm SCREW 4 73 BIASED 8*34mm SCREW 2 74 11*58mm SCREW 2 75 M6x15mm SCREW 2 76 6x13mm WASHER 2 77 8x169mm WASHER 2 78 6x16mm WASHER 8 79 M8x15mm SCREW 12 80 ROUND HEAD M6x60mm SCR 8 81 M8x45 MACHINE SCREW 1 82 M8x70mm SCREW 2 83 FRONT SLEEVE 2 84 SQUARE CAP 4 13 920R Display 920R Display Your Alliance 920R is equipped help you track your progress goals. In order to set your programmable you must begin pedaling. 1. Key Functions: a. RESET - Resetting all cumulative values to zero. b. ENTER - Confirming of “set values,” “selections” and “Quick Start” function. c. + - Increasing and decreasing the set values and resistance during ...