Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Spirit Dateigröße: 608.73 kb Dateiname: c71e0bcc-1116-4023-b05d-fc2db30a04c9.pdf Unterrichtssprache:

Be familiar with its function and limitations. The treadmill will stop, depending on speed, with a one to two step coast anytime the magnet is pulled off the console. Use the red Stop / Pause switch in normal operation. Safety Tether Cord Important Operation Instructions 6 ET6 / ET8 / ET10 Assembly Pack Check List (ET8 / ET6) 5/16.. x1/2.. Button Head Socket Bolt (12 pcs) Lubricant (1pc) Combination M5 Allen Wrench M6 Allen Wrench (1pc) & Phillps Head Screw Driver (1 pc) M5 Speed Nut (6 pcs) 5x 16m/m Screw (6 pcs) Safety Key (1pc) 7 ET6 / ET8 / ET10 Assembly Instructions (ET8 / ET6) 8 ET6 / ET8 / ET10 !!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ BEFORE UNPACKING YOUR FOLDING TREADMILL!! Serious injury could occur if this folding treadmill is not unpacked properly. There is a Velcro strap installed around the treadmill base that prevents the treadmill from unfolding accidentally during shipping. If this strap is not removed properly the treadmill could spring open unexpectedly and cause injury if someone is standing near the treadmill when the strap is removed. To ensure your personal safety during removal of the shipping strap please make sure the treadmill is positioned flat on the ground, in the orientation it would be in if you were using the treadmill. Do not turn the treadmill up on its side while removing the shipping strap. This could cause the treadmill’s folding mechanism to spring open. If the end of the Velcro strap (that you need to grab to remove it) happens to be under the treadmill deck, reach under the deck to grab it, but do not tilt the treadmill up to gain access to the strap end. Assembly ( ET6 / ET8 ) .. STEP 1 Remove all parts from the carton. Locate the left and right frame base covers. Insert six M5 Speed Nuts on the small plates. Install the cover and use six 5 x 16mm Screws to fasten. .. STEP 2 Connect the lower Computer Cable with the middle Computer Cable. .. STEP 3 Hand tighten Right and Left Uprights into the Frame Base with eight 5/16.. x 1/2.. Button Head Socket Bolts, by using the Combination M5 Allen Wrench & Phillips Head Screwdriver .. STEP 4 Connect the middle Computer Cable with the upper Computer cable. Connect the Speed Switch Cable with the upper Speed Cable from the console. Connect the Incline Switch Cable with the upper Incline Cable from the console. .. STEP 5 Install the Console Support into the Right and Left Handrails with four 5/16.. x 1/2.. Button Head Socket Bolts by using the Combination M5 Allen Wrench & Screwdriver. .. PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED. 9 ET6 / ET8 / ET10 Assembly Pack Check List (ET10) 5/16.. x1/2.. Button Head Socket Bolt (10 pcs) Safety Key (1pc) Lubricant (1pc) Combination M5 Allen Wrench M6 Allen Wrench (1pc) & Phillips Head Screw Driver (1 pc) 5/16.. x3/4.. Button Head Socket Bolt (4 pcs) 3/8..x 2.. Button Head Socket Bolt (2 pcs) M5 Speed Nut (4 pcs) 3/8.. x 2T Split Washer (2 5 x 16 m/m Screw (2 pcs) 5 x 16 m/m Tapping Screw (6 pcs) 10 ET6 / ET8 / ET10 Assembly Instructions (ET10) 11 ET6 / ET8 / ET10 Assembly ( ET10 ) .. STEP 1 Remove all parts from the carton. .. STEP 2 Connect the lower Computer Cable with the upper Computer Cable. .. STEP 3 Hand tighten Right and Left Uprights into Main Frame with two 3/8.. x 2.. Button Head Socket Bolts, two 3/8.. x 2T Split Washers and six 5/16.. x 1/2.. Button Head Socket Bolts by using the Combination M5 Allen Wrench & Phillips Head Screwdriver and M6 Allen Wrench. .. STEP 4 Install the Upright Support onto the Left and Right Uprights with four 5/16.. x 3/4.. Button Head Socket Bolts, by using the Combination M5 Allen Wrench & Phillips Head Screwdriver. .. STEP 5 Connect the middle Computer Cable with the upper Computer cable from the console. Connect the Speed Switch Cable with the upper Speed Cable from the console. Connect the Incline Switch Cable with the upper Incline Cable from the console. .. STEP 6 Install the Console Support into the Right and Left Uprights with four 5/16.. x 1/2.. Button Head Socket Bolts, by using the Combination M5 Allen Wrench & Phillips Head Screwdriver. Then Install the Beverage Holder onto the Console Support. * Tighten all screws installed in STEP 4. .. STEP 7 Install the four speed Nuts into side of the Top Motor Cover. .. STEP 8 Install Frame Base Cap (R) and Frame Base Cap (L) with two 5 x 16 m/m Tapping Screws and four 5 x 16 m/m Tapping Screws by using the Combination M5 Allen Wrench & Phillips Head Screwdriver. .. PLEASE LOCK DOWN ALL HARDWARE AFTER THE ACCESSSORIES HAVE BEEN ASSEMBLED. 12 ET6 / ET8 / ET10 Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the desired position. .. To Fold The Treadmill: Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it is secured by the locking telescoping tube assembly in the center of the rear...

Herunterladen

Geben Sie zwei Ziffern: