Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Spirit Dateigröße: 1.91 mb Dateiname: XE100_200_300_OwnersManual_007.pdf Unterrichtssprache:

Then install front stabilizer cover (49) with two M5 x 15m/m Screws (105). 5. Install the Front Handle Bar Covers (54-1 left, 55-1 right) and Rear Handle Bar Cover (54 left, 55 right) over the Handle Bar axle connections with the six 3.5x10m/m Self Tapping Screws (87). 6. Install the front (122) and rear (121) console mast covers with three M5 x 15m/m Screws (105) and two 3.5x12m/m Self Tapping Screws (87). PLEASE ENSURE ALL FASTENERS ARE TIGHT AFTER THE COMPONENTS HAVE BEEN ASSEMBLED. POWER CONNECTOR LOCATED ON FRONT, LEFT HAND SIDE OF UNIT. 11 XE100 / XE200 / XE300 Elliptical XE100 / XE200 12 / XE300 Elliptical Assembly Drawing (XE100) XE100 / XE200 13 / XE300 Elliptical Assembly Drawing (XE200) XE100 / XE200 14 / XE300 Elliptical Step 1 Assembly Pack Check List (XE300) #66. M5 x 10m/m Phillips Head Screw (4pcs) #103. 3/8" x 3/4" Hex Head Bolt (2pcs) #60. 3/8" x 2-1/4" Hex Head Bolt (1pc) #96. 3/8" x 2T Split Washer (1pc) #84. 3/8" x 23 x 1.5T Curved Washer (2pcs) #97.3/8"x30x2T Flat Washer (2pcs) #103. 3/8"x3/4"mm Hex Head Bolt (2 pcs) #81. ..25 Wave Washer (2 pcs) #87. ..3.5x12m/m Self Tapping Screw (8pcs) Step 2 XE100 / XE200 15 / XE300 Elliptical Step3 #87. ..3.5x12m/m Self Tapping Screw (10pcs) #105.M5 x 15m/m Phillips Head Screw (11pcs) #104. 5/16.. x 1-1/4.. Hex Head Bolt (2 pcs) #80. 5/16" x 20x 1.5T Flat Washer (2 pcs) #71. 5/16" x 7T Nylon Nut (2 pcs) Step 4 #105.M5 x 15m/m Phillips Head Screw (26pcs) #91. 5/16"x 3/4.. Hex Head Bolt (4 pcs) Tools #108. Phillips Head Screw Driver (1 pc) #107. Short Phillips Head Screw Driver (1 pc) #109. 12m/m Wrench (1pc) #106. 13/14m/m Wrench (1pc) 16 XE100 / XE200 / XE300 Elliptical XE100 / XE200 17 / XE300 Elliptical .. UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. STEP 1: CONSOLE MAST ASSEMBLY 1. Locate the Console Mast (12) and Console Mast Cover (41) and slide the Cover onto the Mast as far as it will go. Make sure the Console Mast Cover is facing the correct way. 2. At the top opening of the Main Frame of the elliptical is a Computer Cable. Unravel and straighten out the Computer Cable (31) and feed it into the bottom of the console mast tube and out of the top opening. 3. Install the Console Mast into the receiving bracket in the top of the Main Frame. NOTE: there is one bolt already installed in the receiving bracket that will engage with the slot at the bottom of the Console Mast. This needs to be tightened at the end along with the three other console mast bolts. 4. Put one 3/8" x 2T Split Washer (96) onto the 3/8" x 2-1/4" Long Hex Head Bolt (60), and the two 3/8" x 23 Curved Washers (84) onto the two 3/8" x 3/4" Short Hex Head Bolts (103). Install, and hand tighten, the Long Hex Head Bolt through the left side of the receiving bracket into the Console Mast. NOTE: There is an electrical wire running through the Console Mast Tube. Be careful not to damage or pinch this Computer Cable during this procedure. Damage to the Console could result. Install, and hand tighten, the two Short Hex Head bolts through the front of the receiving bracket into the Console Mast. 5. Using the 13/14m/m Wrench tighten the three bolts and the fourth bolt, which is pre-installed, firmly. These bolts should be tightened as much as you possibly can. 6. There will be three electrical wire connectors at the top opening of the console mast, two 2 pin connectors (hand pulse sensors)(36) and one 10 pin connector (main wire harness)(31). Connect these to the mating connectors on the back of the electronic Console (30). The connectors are keyed, you cannot plug them in the wrong way so do not force them. The two, 2 pin connectors can be plugged into either connector on the back of the console. 7. Storing the excess wire back into the Console Mast, carefully install the Console onto the mounting plate of Console Mast and secure using the four M5 x 10m/m Phillips Head Screws. Make sure the wires do not get pinched between the console and mounting plate. Assembly Instructions (XE300) XE100 / XE200 18 / XE300 Elliptical STEP 2: HANDLE BAR ASSEMBLY 1. Install the two 28m/m Wave Washers (81) onto the Left and Right side of the Handle Bar axle. 2. Slide the Left (10) and Right (11) Handle Bars onto the appropriate side of the axle. The handlebars have a small sticker on them indicating L (left) and R (right). 3. Put the two 3/8 X 30mm Flat Washers (97) onto the two 3/8.. X 3/4.. Hex Head Bolts (103) and install, and tighten, in the threaded holes in the ends of the axle. 4. Connect the two wires together (124, 125) and store the excess, including plastic connectors,...

Herunterladen

Geben Sie zwei Ziffern: