Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Horizon Fitness Dateigröße: 2.57 mb Dateiname: Unterrichtssprache:

It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken. UNPACKING Unpack the product where you will be using it. Place the product on a level flat surface. It is recommended that you place a protective covering on your floor. During each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. NOTE: A light application of grease may aid in the installation of hardware. Any grease, such as lithium bike grease is recommended. Before proceeding, find your elliptical’s serial number located on the front stabilizer tube and enter it in the space provided below. Also locate the model name which is located on the side cover badge. enter your serial number and model name in the boxes below: SERIAL NUMBER : MODEL NAME: * Refer to the serial number and model name when calling for service. * Also enter this serial number on your Warranty Card. WARNING IMPORTANT PRECAUTIONS TOOLS INCLUDEDPARTS INCLUDEDc 5mm Allen Wrenchc Phillips Screw Driverc 13/15mm Flat Wrenchc 1 Consolec 1 Console Mastc 1 Front Stabilizer Tubec 2 Upper Handlebarsc 2 Lower Handlebarsc 2 Lower Link Armsc 2 Pivoting Foot PadsCONSOLE (E700/E800 SHOWN) UPPER HANDLEBARMAIN FRAMELOWER HANDLEBARLOWER LINK ARMFRONT STABILIZER TUBEGRIP PULSECONSOLE MASTPIVOTING FOOT PADS(E800 SHOWN) PEDAL ARMc 1 Top Coverc 1 Top Cover Grommetc 6 Hardware Bagsc 1 Water Bottle Cagec 1 HORIZON FITNESS 12-volt Power Supplyc 1 Audio Adaptor Cable (E700 & E800 only) WATER BOTTLE CAGEMP3 STORAGE SPEAKERS (E700/E800 ONLY) E800 SHOWN If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. For a complete exploded diagram, visit us at COVER ASSEMBLY STEP 1 MAIN FRAMEFRONT STABILIZER TUBESCREW (A) A) Open HARDWARE BAG FOR STEP 1. B) Attach the FRONT STABILIZER TUBE to the MAIN FRAME using 2 BOLTS (A). HARDWARE BAG FOR STEP 1 CONTENTS : SCREW (A) 20 mmQty: 2 MAIN FRAMEREAR STABILIZERBOLT SPRING WASHER (B) FLAT WASHER (C) SCREW (B) ASSEMBLY STEP 2 A) Open HARDWARE BAG FOR STEP 2. B) Secure REAR STABILIZER to MAIN FRAME using 2 SCREWS (B). NOTE: Make sure holes are aligned before inserting SCREWS. HARDWARE BAG FOR STEP 2 CONTENTS : SCREWS (B) 30 mmQty: 4 ASSEMBLY STEP 3 CONSOLE WIRESTOP COVERCONSOLE MASTGROMMETMAIN FRAMEBOLTS (C) LOCK WASHERS (D) * Note: Be careful not to pinch any wires while assembling the mast. A) Open HARDWARE BAG FOR STEP 3. B) Slide the GROMMET and TOP COVER over the CONSOLE MAST. C) Carefully pull the CONSOLE WIRES through the CONSOLE MAST using the twist tie located inside the CONSOLE MAST. D) Attach CONSOLE MAST to MAIN FRAME using 7 BOLTS (C) and 7 LOCK WASHERS (D). E) Slide GROMMET and TOP CAP down to seal the MAIN FRAME. HARDWARE BAG FOR STEP 3 CONTENTS : BOLTS (C) 15 mmQty: 7LOCK WASHER (D) 13.5 mmQty: 7 ASSEMBLY STEP 4 PRE-ATTACHED SCREWSTABUPPER HANDLEBARHANDLEBAR JOINTLOWER HANDLEBARNOTCH NOTE: There is NO hardware bag for this step. A) Slide LOWER HANDLEBAR onto CONSOLE MAST and align NOTCH with TAB making sure bars are joined together completely. Secure LOWER HANDLEBAR to CONSOLE MAST using PRE-ATTACHED SET SCREWS. B) Slide UPPER HANDLEBAR onto CONSOLE MAST and align NOTCH with TAB making sure bars are joined together completely. Secure UPPER HANDLEBAR to CONSOLE MAST using PRE-ATTACHED SET SCREWS. C) Repeat on other side. After handlebars are assembled they will rotate freely – be cautious. Until the machine is fully assembled, do not grab the handlebars for support. WARNING M5x20mm Screwquantity:4B) M5x15mm Screwquantity:8quantity:6D) M8x15mm Screwquantity: 2C) 29mm wave washerSCREW (E) LOWER LINK ARMFOOTPAD ASSEMBLY STEP 5 E800 SHOWN A) Open HARDWARE BAG FOR STEP 5. B) Attach FOOTPAD to LOWER LINK ARM using 4 SCREWS (E). C) Repeat on other side. HARDWARE BAG FOR STEP 5 CONTENTS : SCREW (E) 20 mmQty: 4SCREW (E) 15 mmQty: 8SCREW (G) 29 mmQty: 6SCREW (H) 15 mmQty: 2 A) M5x20mm Screwquantity:4B) M5x15mm Screwquantity:8quantity:6D) M8x15mm Screwquantity: 2C) 29mm wave washerFOOTPADWASHER (F)SCREW (G)FOOTPAD BRACKETPEDAL ARMLINK ARM ASSEMBLY STEP 6 E800 SHOWN A) Open HARDWARE BAG FOR STEP 6. B) Place WASHER (F) over the LINK ARM axle. C) Slide LINK ARM into PEDAL ARM. D) Attach FOOTPAD BRACKET to the LINK ARM with 3 SCREWS (G). E) Repeat on other side. HARDWARE BAG FOR STEP 6 CONTENTS : SCREW (E) 20 mmQty: 4SCREW (F) 15 mmQty: 8WAVE WASHER (F) 20 mmQty: 2SCREW (G) 15 mmQty: 6 M5x20mm Screwquantity:4B) M5x15mm Screwquantity:8quantity:6D) M8x15mm Screwquantity: 2C) 29mm wave washerLOWER HANDLEBARSPACER RING (G) SPACER (H) BOL...

Herunterladen

Geben Sie zwei Ziffern: