Stimmen - 4, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
45 The Optional Power Adapter Kit .................................................... 45 Replacing the Battery ........................................................................ 46 Commercial Cardiovascular Equipment Limited Warranty ..... 47 Chapter 1 Assembling the AMT Important: The instructions in the following procedures are described from the perspective of a person standing directly in front of the equipment (that is, on the opposite side of the control console from a person using the equipment). These descriptions may not match the names of certain parts in the parts list, because such parts are named relative to the back of the equipment. To prepare the AMT for assembly: . Open the box and assemble the components in the sequence presented in this guide. . Assemble and operate your equipment on a hard, level surface in the area intended for use. Important: Do not grasp any plastic parts of the unit while lifting or moving the unit. The plastic parts are non-structural covers and are not capable of supporting the weight of the unit. . Provide ample space around the unit. . Assemble the equipment according to the guidelines in this manual to ensure you do not void the Precor Limited Warranty. Important: Any damage caused during installation is not covered by the Precor Limited Warranty. . Attach all fasteners and partially tighten them. Do not fully tighten fasteners until instructed to do so. WARNING You will need assistance to assemble this unit. DO NOT attempt assembly by yourself. Hardware Kit (not to scale) The hardware kit shipped with this equipment contains the fasteners and other hardware components shown in the following table. Before you begin assembly, make sure that your hardware kit is complete. If not, please contact Precor Customer Support. Fasteners Quantity Locknuts (....-inch) 8 Hex head screws (....-inch x 1...-inch) 4 Flat washers (....-inch) 8 Flat head hex drive screws (...-inch x ...-inch) 4 Plastic boots 2 End caps 2 Required Tools . ....-inch hex wrench . ....-inch hex wrench . #2 Phillips screwdriver . Rubber mallet . SAE standard socket set . Wire cutter . Torque wrench (calibrated in inch-pounds) Performing the Assembly DANGER Do not attempt to connect electrical power until all assembly procedures are complete and the console is properly installed. Follow these steps to assemble the AMT base unit. To begin assembly: 1. Remove the two side fasteners that hold the front frame tube to the shipping pallet and cut the tie wraps that secure the rear base. CAUTION: Do not move the AMT off its shipping pallet without assistance. To avoid unnecessary movement of the foot plates, do not install the handlebars until you begin the next procedure. 2. Lift the rear base and roll the AMT forward while your assistant stabilizes the front base and guides it off the shipping pallet onto the floor. Note: Begin assembly in the area intended for use. 3. Insert the end caps into the front frame tube. If necessary, use a rubber mallet to tap them into place. Figure 2: Removal of unit from pallet and insertion of end caps To attach the handlebars: 1. Slide a plastic boot onto each handlebar. Figure 3: Boot attachment 2. Use the following graphic to determine the proper position of the handlebars. Note: When the handlebars are mounted correctly, each bends slightly outward. Figure 4: View of handlebar placement 3. Attach the handlebars using four ....-inch x 1.-inch hex head screws, eight ....-inch washers, and four ....-inch locknuts. Using a torque wrench, tighten the fasteners with 180 to 200 inch-pounds of torque. Figure 5: Handlebar attachment 4. Rotate the plastic boot so that its tab aligns with the cutout below it, and then press the boot downward to secure it in place. Removing Access Covers With its access covers removed, the AMT provides easy access to its cables and internal components. Tip: In the following procedure, set aside the covers and their mounting hardware in groups, in the order in which you remove them. This simplifies reinstallation later. To remove the access covers: 1. Using a rubber mallet or the heel of your hand, tap at an upward angle against the side of the top column cover to snap it loose. Figure 6: Where to place pressure when removing top cover 2. Lift the cover, then slide it toward the rear of the equipment and out. 3. Using a ....” hex wrench, disconnect the two 1-inch buttonhead screws at the bottom of the front cover, then snap the cover loose. Threading the Cables Depending on the model of console you are installing and the options it includes, you will need to install one or more of the following cables: . Television (coaxial with F connectors) . Power . Ethernet Precor recommends threading new cables from the top down, to take advantage of gravity. A fish tape (a thin metal strip with a hook or clasp on one end, available from professional hardware vendors) can be helpful during this procedure. To thread new cables through the equipment: 1. Sele...