Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Before reading further, please review the drawing below and familiarize yourself with the labeled parts. Handrail UprightStorage Latch Key/Clip Reset/Off Circuit Breaker Walking Belt Cushioned Walking Platform for maximum exercise comfort Foot Rail Power Cord RIGHT SIDE Rear Roller Adjustment Bolts Console Fan Accessory Tray BACK 5 ASSEMBLY To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Assembly requires the included allen wrenches and your own phillips screwdriver , rubber mallet , adjustable wrench , and wire cutters . For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, check to see if it has been pre-assembled. Nut (47)–4 Handrail Bolt (20)–4 Endcap Screw (95)–4 Upright Bolt (40)–4 Frame Washer (33)–2 1/4” Star Washer (21)–2 Silver Ground Screw (27)–2Wheel Spacer (44)–4 Console Bolt (22)–2 Frame Bolt (32)–2 Wheel Bolt (89)–2 3/4” Screw (2)–8 Upright Star Washer (39)–4 Handrail Star Washer (19)–4 1. Make sure that the power cord is unplugged. Have a second person hold the Upright Base (48) in the position shown, with the wheel holes at the top. Identify the Left Upright (31), which is marked with a sticker. Orient the Left Upright so the indicated bracket is in the position shown, and attach the Left Upright to the Upright Base with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet. 48 Wheel Holes Bracket 40 39 31 1 6 7 2. Orient the Right Upright (36) so the square hole near the lower end is in the position shown. Attach the Right Upright to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet. Attach each Wheel (45) to the Upright Base (48) with a Wheel Bolt (89), two Wheel Spacers (44), and a Nut (47) as shown. Do not overtighten the Wheel Bolts; the Wheels should turn freely. 48 Square Hole 45 47 44 89 45 44 36 44 89 47 3. Cut the tie securing the Wire Harness (28) in a bundle. Do not remove the large colored tie on the end of the Wire Harness. Orient the Upright Base (48) so the Wheels (45) are at the bottom. Next, position the Upright Base and the Uprights (31, 36) around the frame assembly as shown. Have another person lift the front of the frame assembly and hold it. Insert the Wire Harness (28) into the square hole near the lower end of the Right Upright (36) and out of the top. Next, raise the Uprights (31, 36) so the Upright Base (48) is flat on the floor. Make sure that the end of the Wire Harness does not fall into the Right Upright; it may be helpful to hold the colored tie on the end of the Wire Harness. 28 Colored Tie 48 28 36 31 45 3 4. Open the included grease packet, and apply equal amounts of grease to both sides of each Frame Spacer (34). Hold one of the Frame Spacers (34) between the frame assembly and the Right Upright (36); make sure that the Frame Spacer is oriented as shown in the inset drawing. Insert a Frame Bolt (32) through a Frame Washer (33), the Right Upright, the Frame Spacer, and the bracket on the frame assembly. Be careful not to pinch the Wire Harness (28) in the Right Upright. Tighten a Nut (47) several turns onto the Frame Bolt, but do not fully tighten the Nut yet. Repeat this step on the left side. Note: There is not a wire harness on the left side. Remove the colored tie from the Wire Harness (28). Frame Assembly Frame Assembly Hole 32 59 34 34 33 4 47 28 36 Right Side Left Side 34 40 39 Colored Tie 2 8 28 18 6. Hold the Console Base (26) near the right Handrail (18). Attach the end of the ground wire on the Console Base to the indicated small hole in the Handrail with a Silver Ground Screw (27). Connect the Wire Harness (28) to wire harness on the Console Base (26). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 27 26 Ground Wire 22 7. Set the console assembly on the Handrails (18); insert the excess wiring down into the right Handrail. Attach the console assembly with four 3/4” Screws (2), two Console Bolts (22), and two 1/4” Star Washers (21) as shown. Make sure that no wires are pinched....