Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Huffy Dateigröße: 879.51 kb Dateiname: Unterrichtssprache:

• Do not slide, climb, shake or play on pole. • When adjusting height, keep hands and fingers away from moving parts. • Do not allow children to move or adjust system. • During play, do not wear jewelry (rings, watches, necklaces, etc.); objects may entangle in net. • Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and or deterioration. • Check pole system for signs of corrosion (rust, pitting, chipping) and repaint with with exterior enamel paint. If rust has penetrated through the steel anywhere, replace the pole immediately. • Check system before each use for proper ballast, loose hardware, excessive wear and signs corrosion and repair before using. • Check system before each use for instability. • Never play on damaged equipment. • Keep pole top covered with cap at all times. 201255 2/99 1-800-558-5234 37 P/N 211560H 01/03 2 Ensure ground is level with playing surface, then dig pole hole. 1. 1. WARNING CONTACT UTILITIES BEFORE DIGGING. 24" (61 cm) 36" (91.4 cm) GROUND SURFACE PLAYING SURFACE Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. NOTE: Make sure J-bolts (1) are in the illustrated position. NOTE: Nuts on the top of plate are used for leveling the pole after system is fully assembled. 2. 3 2 22 1 3. 1 Install nut (2) to J-bolt (1) as shown. Repeat procedure for other three J-bolts (1). 2” (5.08 cm) IMPORTANT! Make sure nuts are 2” (5.08 cm) from top of J-Bolts. 3 01/03 P/N 211560H Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. 4. ........4. ........ 5. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any excess cement on mounting plate at this time. NOTE: Check leveling of mounting plate (3) PLAYING SURFACE ........................................................................several times while concrete is curing. IMPORTANT! Front of mounting plate (3) must be parallel with playing surface. DO NOT PROCEED TO STEP 6 UNTIL CONCRETE HAS CURED FOR A MINIMUM OF 72 HOURS. ALLOW ADDITIONAL TIME FOR COLD, WET OR HUMID WEATHER. WARNING 3 P/N 211560H 01/03 4 Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING PLAYING SURFACE PLAYING SURFACE IMPORTANT! Holes in pole must be parallel with playing surface. 4 38 3 7 6 Note: Offset holes go to back of system. 4 5 1 Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING PLAYING SURFACE PLAYING SURFACE IMPORTANT! Holes in pole must be parallel with playing surface. 4 38 3 7 6 Note: Offset holes go to back of system. 4 5 1 5 01/03 P/N 211560H 8. 8. Insert caps (8) into end of each support arm (9 & 10) as shown. Tap firmly in position. 9. Apply logo label (11) to lower support arms (10) as shown. Repeat for opposite side. Beginning with upper support arms (9) secure TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING support arms to pole. Continue by securing lower support arms (10) as shown. IMPORTANT! Do not over tighten. SHORT END 9 10 11 10 8 8 8 8 12 7 4 4 9 5 4 4 10. 7 7 4 8 8 Note: This bolt rests outside the upright pole. 12 4 4 4 P/N 211560H 01/03 6 11. 16 4 13 9 4 7 4 10 7 4 10 7 4 16 4 7 4 9 16 4 16 TWO PER...

Herunterladen

Geben Sie zwei Ziffern: