Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Install pole mount assembly and reinforcement bracket (47) with carriage bolts (46) to pole as shown. Tighten flange nuts (15) completely. 22. Push back sliding pin (43) as shown in Figure A to fit adjustable system assembly through pole mount assembly. Then attach spring covers (48 & 49) onto pole mount bracket (45) with bolt (50), and nut (15) as shown in Figure B. 23. Attach backboard support brackets (52) to the backboard frame using bolts (53), spacers (51), and nuts (37) as shown. 24. Attach lower elevator tubes (56) and spring (68) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. NOTE: Rim mounting nuts and bolts (60) supplied with rim hardware. 25. Attach upper elevator tubes (63) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. 26. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Then install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 27. Install upper elevator tubes (63) to triangle plates (66) as shown. Install handle assembly to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Tighten bolt (57) in lock nut (58) until flush (even) with lock nut’s outer edge. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 28. WARNING: USE EYE PROTECTION WHEN INSTALLING SPRINGS. Insert bolt (57) through left side upper elevator tube (63), then stretch springs (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). 29. Attach front cover (54) to hinge tubes (24) using carriage bolt (42) and flange nuts (15) as shown. 30. WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY, MAY TIP OVER. Apply height and moving label (76) to front of pole as shown. 31. Roll completed assembly to desired playing area. Secure assembly to ground using strap (61) and tie down stake (7). Fill tank with 34 gallons of water. IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in sub-freezing climates. Add two gallons (7.6 liters) to tank to prevent freezing in sub-freezing climates. Snap cap (62) into place. WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. 32. Grasp handle and depress lever. 33. Push toward pole while holding lever. Raise or lower lever to desired height while pushing forward on handle. 34. Release handle making sure that horizontal pin (43) is locked into slot. WARNING: USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. 35. Install net clips as shown. (See illustration) 36. Install net as shown. (See illustration) 5 06/03 P/N 211972B IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL 1. 5" (13 cm) MIDDLE TOP 5" (13 cm) BOTTOM 1 3 2 2. 2 Note (See Text Page) IMPORTANT! (See Text Page) Note (See Text Page) IMPORTANT! (See Text Page) 1 3. 1 Wood Scrap 2 3 P/N 211972B 06/03 6 4. 5. 16 17 29 25 17 28 16 29 15 5 3 6. Note (See Text Page) 4 1 2 61 11 8 6 61 8 4 5 11 7. 10 11 9 3 11 12 13 9 9 7 06/03 P/N 211972B P/N 211972B 06/03 8 8. 9. 8 20 18 19 26 25 15 24 13. 21 30 20 8 11. Note (See Text Page) 14 11 11 15 9 18 23 20 22 21 20 8 10. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORTANT!: 12. 29 27 28 25 27 29 9 06/03 P/N 211972B 14. ELEVATOR INSTALLATION (See steps 14-21) 32 33 32 31 15. 16. 11 15 11 15 34 35 35 34 39 31 11 32 37 11 36 11 11 39 38 34 Note (See Text Page) 17. 32 33 40 19. 33 41 IMPORTANT! (See Text Page) WARNING (See Text Page) 18. 32 P/N 211972B 06/03 10 22. FRONT SIDE 20. 44 45 44 43 43 Note (See Text Page) WARNING (See Text Page) 1 46 45 15 15 47 21. Fig. B Fig. A 50 45 48 15 43 49 68 58 52 15 59 68 24. 59 57 60 56 56 52 Note (See Text Page) 69 51 51 53 53 37 52 52 Refer To Instructions Included With Rim Hardware For Rim Assembly. 23. 68 58 52 15 59 68 24. 59 57 60 56 56 52 Note (See Text Page) 69 51 51 53 53 37 52 52 Refer To Instructions Included With Rim Hardware For Rim Assembly. 23. 11 06/03 P/N 211972B 25. 57 59 59 63 52 58 56 63 56 26. Note (See Text Page) 1 66 56 67 56 57 67 58 65 66 64 P/N 211972B 06/03 12 13 06/03 P/N 211972B 28. WARNING (See Text Page) 57 63 58 68 63 27. Note (See Text Page) 63 58 56 67 58 67 67 57 56 57 67 63 66 P/N 211972B 06/03 14 43 ELEVATOR HEIGHT ADJUSTMENT 32. 33. 34. 71 61 62 7 31. IMPORTANT! (See Text Page) WARNING (See Text Page) Peel protective film from surface of acrylic backboard prior to use. NOTE: 10 feet (3.05m) 30. 54 29. WARNING (See Text Page) 42 15 24 35. IInnssttaallll nneett cclliippss.. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. CLIP “ARM” CLIP “BODY” 69 55 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so ...