Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Huffy
Dateigröße: 531.14 kb
Dateiname: a635155b-faa6-e224-3de9-99fa1b834603.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
* IMPORTANT! Holes in top and bottom pole sections MUST align to correctly position elevator system. Continue to check alignment while assembling pole sections. *Row of 3 holes on top pole section must be parallel with adjustment knob. Once assembled, pole sections can NOT be separated! POLES MUST OVERLAP 3-1/2” (9 CM) MINIMUM. NOTE: Discard this carriage bolt immediately after completing this step. DO NOT discard flange nut and washer. 6 printed on recycled paper 4 P/N 211387 5/99 6. 6. Attach base pole bracket (10) and base strut brackets (11) to base (1) as shown below. 10 12 11 1 11 13 13 8 8 12 12 13 8 15 10 13 14 15 8. 13 13 17 16 14 14 7. Attach struts (14) as shown above. Attach pole strut bracket (16) to struts (14) as shown at left. SAND BALLASTSAND BALLSAND 9. Place tank (1) in desired location. Fill tank (1) with water (30 gallons (114 liters)) or sand (360 lb. (163 kg)). Snap tank cap (18) in place. 18 1 IMPORTANT! Add two gallons (7.6 liters) of NON-TOXIC ANTIFREEZE in sub-freezing climates. printed on recycled paper 5 5/99 P/N 211387 10. Rest pole assembly on FILLED tank. WARNING KEEP UNNECESSARY PRESSURE OFF OF THE POLE ASSEMBLY WHEN IN THIS POSITION. TWO PEOPLE RECOMMENDED FOR THIS STEP. Attach lower halves of backboard brackets (23) to swivel bracket (21). NOTE: Keep hardware loose until after alignment in step 16. 13. 23 12 13 13 12 21 Attach upper pole mounting bracket (20) to swivel bracket (21) and fully tighten. 12.21 22 8 12 20 Attach pole assembly to pole bracket (10) as shown. NOTE: Keep unnecessary pressure off of the pole assembly when in this position. Two people recommended for this step. 11. 8 13 19 10 printed on recycled paper 6 P/N 211387 5/99 NOTE: Two people recommended for this procedure. Attach bracket assembly to top pole section (5). Secure hardware as shown and tighten completely. Install pole cap (25). 14. 14. PLAY POSITION STORAGE POSITION 24 13 7 25 5 8 Attach back bracket (26) to backboard and backboard brackets (23) as shown and finger tighten. NOTE: Do NOT tighten completely. Final adjustments will be made in step 24. 16. 23 23 13 27 27 27 13 Bend upper halves of backboard brackets (23) to line up with mounting holes on backboard as shown. 15. 26 printed on recycled paper 7 5/99 P/N 211387 Assemble rim (28) to back bracket (26) as shown.17. 17. 29 22 8 28 30 31 26 18. 32 33 31 19. 28 34 USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF NET CLIPS, OR WHEN ALL NET CLIPS ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. WARNING Install net (35).20. INSIDE VIEW 35 28 21. Attach nylon tie down stake rope (36) to tank (1) as shown. 1 36 Secure unit to ground using nylon rope (36) and tie down stake (37). 37 3622. 21. Attach nylon tie down stake rope (36) to tank (1) as shown. 1 36 Secure unit to ground using nylon rope (36) and tie down stake (37). 37 3622. NOTE: Two people recommended for this procedure. Level backboard and rim adjust hardware from step 13 and 16. Tighten completely. Regulation rim height is 10 feet (3.05 m). 24. Apply height adjustment label (40) to front of pole as shown.25. 10 feet (3.05 m) 23. Carefully upright pole and backboard assembly. Secure strut assembly (14) to bottom pole section (4) as shown. 38 40 14 9 8 4 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING HEIGHT ADJUSTMENT Rest unit on support table. Remove adjustment knob (9), carriage bolt (7), and washer (8) to extend or retract pole. Pole adjusts from 71/2’ to 10’. Re-Insert Adjustment set (7, 8, 9) When pole is at desired height. 91. 8 BACKBOARD AND TOP POLE MAY ROTATE DURING HEIGHT ADJUSTMENT. WARNING SUPPORT TABLE 7 TO PLACE IN THE STORAGE POSITION Lower backboard and rim down to the lowest position (71/2’ (2.29 m)). Remove adjustment knob (9), washer (8), and carriage bolt (7). Carefully rotate pole downward towards ground. 1. 2. 7 1 DO NOT STAND BEHIND SYSTEM WHEN PREPARING FOR STORAGE. WARNING 3. Secure pole assembly to tank (1) with carriage bolt (7), washer (8), and adjustment knob (9). Remove adjustment knob (24) from swivel bracket (21) and carefully rotate backboard assembly 180.. PLAY POSITION 24 8 STORAGE POSITION 4. 8 Secure backboard assembly in storage position with adjustment knob set (24 and 8) as shown. 9 P/N 211387 5/99 10 printed on recycled paper 33 5. Remove knob set (32, 31, and 33) from the rim assembly and re-insert knob set into top locking position. 32 31 6. Carefully rotate system up on its side to remove water or sand from tank. 50" (127 cm) Secure screw hook (39) into wall, approximately 50” (127 cm) up from floor as shown. IMPORTANT! It is necessary to install screw hook into a wall stud. Remove tie down stake (37) from ground and detach rope (36). Rotate system up onto the front wheels and roll toward the wall. Secure system with rope (36) on screw hook (39). 39 36 8. 7. 3639 printed on recycled paper 11 5/99 P/N 211387 ...