Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
The PE980 is a sensor type pedometer that can detect steps in any dimension it is carried. It is equipped with clock, alarm, 7-day memory, step counter, distance counter and calorie counter functions. IMPORTANT Do not immerse the pedometer in water. CONTROL BUTTONS 1 2 3 1. SET: Enter Setting Mode; confi rm and move to next setting option 2. DISP: Display calorie burned and distance walked; increase values 3. MEM: Enter Memory Mode; decrease values LCD 1 10 11 12 13 23 4 7 89 6 5 14 15 16 17 19 18 1. : Indicates calorie burned is displayed 2. : Indicates beep tone is Off 3. : Indicates battery power is low 4. Displays mode banners, number of steps, calorie reading or distance walked 5. : Indicates alarm is On 6. : Indicates exercise timer is displayed 7. : Indicates on which day (1-7) before is the displayed data recorded 8. / : 12 hour clock 9. Displays time or Setting Mode values 10. : Indicates distance walked is displayed 11. : Indicates you are in Memory Mode 12. : Indicates there is a following page 13. : Smart indicators to press the button beside 14. : Indicates step counter is On 15. : Indicates there is a previous page 16. : Calorie unit 17. : Distance unit (Miles / Kilometres) 18. : User’s stride length unit (Centimetres / Inches) 19. : Weight unit (Pounds / Kilograms) GETTING STARTED ACTIVATE PEDOMETER (FIRST-TIME USE ONLY) Press and hold any key until the screen is activated. CARRYING THE PEDOMETER The PE980 can be carried on the waist, around the neck or in pockets and handbags by using the adjustable strap or detachable clip provided. SET TIME AND USER DATA To effectively use the pedometer for calculating calorie burned (based on step count and user body weight) and distance walked (based on step count and length of user’s stride), you are advised to set the time and your user data in the Setting Mode. Refer to Setting Mode in this manual. EN IMPORTANT Remember to set the time and your user data after every battery replacement. BATTERY REPLACEMENT The pedometer uses a CR2032 3V battery, which has already been installed. Indicates battery power is low. To replace battery: 1. Use a small Phillips screwdriver to remove battery compartment lid. Once opened, please keep the screws in a safe place to avoid losing them. 2. Remove the old battery and insert the new one, matching the polarities. 3. Replace the lid by screwing it back into place using a Phillips screwdriver. NOTE When the battery compartment is opened or battery is replaced, all data in the pedometer will be reset. OPERATION MODES The PE980 has 3 modes of operation. The Main Mode is the default display mode, which displays the current step count and time. To enter other modes, press the buttons as shown below. MAIN MODE In the Main Mode, you can: • view the time and current step count (default), calorie burned, distance walked and exercise time • turn On or Off the step counter To view the current calorie burned and distance walked: Press DISP. The display sequence is: calorie burned and distance walked . The exercise time with icon is also displayed. To turn the step counter On or Off: In situations where you do not need to record step count, you can turn Off the step counter. Press and hold SET and MEM at the same time for 2 seconds until the following screen is displayed. To turn On the step counter, repeat the same action. indicates step counter is On. or NOTE • If the step counter is Off, there will be no step, calorie and distance calculation or recording into memory. • The current step count, calorie burned, distance walked, and exercise timer will be reset automatically to zero at midnight. SETTING MODE In the Setting Mode, you can set the time, alarm On/Off and alarm time, user’s weight and stride length, and beep tone On/Off. 1. Press SET to enter the Setting Mode. 2. Wait for the setting option to fl ash, then press DISP or MEM to set values. You can press and hold these buttons to rapidly set the values. 3. Wait 3 seconds for the pedometer to automatically confi rm and move to the next setting option. The setting sequence is: stride length unit, stride length value, weight unit, weight value, 12/24 time format, time (hour and minute), alarm On/Off, alarm time (hour and minute) (if alarm On is selected) and beep tone On/Off. NOTE You can press SET to skip through settings. REMARK Press any button to silence an activated alarm. If not deactivated, the alarm will be activated at the same time the following day. MEMORY MODE In the Memory Mode, you can view the records of your steps and calories burned for the past 7 days. 1. Press MEM to enter the Memory Mode. 2. Press DISP or MEM to select which day to view. NOTE • When toggling between days, the record displayed will be of the same category (either step count or calorie burned). • When viewing a day’s record, the pedometer will automatically toggle for 3 seconds between step count and calorie burned display. REMARK Toggle through all 7-day records to return to the Main Mode. ...