Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Veillez a laisser un degagement d'au moins 30 cm devant l'appareil. . VERIFIEZ si l'emballage contient toutes les pieces de la liste jointe avant de le mettre de cote. Si des pieces sont absentes, contactez le service apres-vente de Life Fitness au numero indique dans le manuel d'utilisation. Conservez l'emballage au cas ou vous devriez renvoyer l'appareil. . LISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet appareil. Ceci est indispensable a son utilisation correcte. TOOLS REQUIRED FOR ASSEMBLY... Phillips Screwdriver, T27 Torx Screwdriver, Socket Set PARTS DESCRIPTION 1 Hex Head Bolt 3/8 – 16 x 3 Qty: 2 3 Hex Head Bolt 5/16 – 18 x 1.500 Qty: 2 5 Phillips Pan Head Screw (Model 93S) #8 – 18 x .625 (Model 90S) Qty: 8 Qty: 4 7 Phillips Pan Head Screw #8 – 18 x .75 Qty: 4 9 Display Console Assembly Qty: 1 11 Accessory Tray (Model 93S) Qty: 1 13 Left Bullhorn Handlebar (Model 93S) Qty: 1 15 Handlebar Assembly Qty: 1 17 Telemetry Cable (Model 93S) (Model 90S International) Qty: 1 Qty: 1 19 Polar Cover Qty: 1 2 Lock Nut 3/8 – 16 Qty: 2 4 Torx Cap Screw (Model 93S) 1/4 – 20 x .625 (Model 90S) Qty: 4 Qty: 10 6 Flat Head Screw (Model 93S) 1/4 – 20 x .625 Qty: 6 8 Phillips Cap Screw #6 – 32 x .375 Qty: 2 10 Monocolumn Qty: 1 12 Vertical Handrail Qty: 2 14 Right Bullhorn Handlebar (Model 93S) Qty: 1 16 Polar® Receiver (Model 93S) (Model 90S International) Qty: 1 Qty: 1 18 Frame Cap Qty: 2 20 Monocolumn Shroud Qty: 1 1 2 543 6 7 8 10 20 C D B 20 10 E B 2 1 15 F 10 D H 1. Before proceeding, familiarize yourself with the parts of the Stairclimber and make sure that you have received all the items described in the Parts List. 2. Locate the MONOCOLUMN (#10). Position the MONOCOLUMN SHROUD (#20) onto the MONOCOLUMN as shown. Position the MONOCOLUMN near the MONOCOLUMN MOUNTING BRACKET (B) as shown. Detach and feed the CONSOLE WIRE HARNESS (C) through the MONOCOLUMN and out through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. Pivot the MONOCOLUMN upright and position the locating slot at the bottom of the MONOCOLUMN onto the preinstalled LOCATING BOLT (E) on the MONOCOLUMN MOUNTING BRACKET. Align the mounting holes of the MONOCOLUMN and MONOCOLUMN MOUNTING BRACKET and secure them together using two MOUNTING BOLTS (#1) and LOCKNUTS (#2). Leave the NUTS and BOLTS loose at this time. Lower the MONOCOLUMN SHROUD until it rests on the MAIN SHROUDS. (Model 90S) The forward most of the two MOUNTING BOLTS (#1) and LOCKNUTS (#2) will pass along the outside of the MONOCOLUMN (#10). CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HARNESS (C). MISE EN GARDE : VEILLEZ A NE PAS PINCER LE FAISCEAU (C). 3. Align and insert the HANDLEBAR ASSEMBLY (#15) into THE HANDLEBAR BRACKET TUBE (F) as shown until the mounting holes in the HANDLEBAR ASSEMBLY align with those of the HANDLEBAR BRACKET TUBE. Model 93S Shown 14 15 F 10 13 6 J 19 8 15 F 8 16 4. (Model 93S / 90S International) Locate the TELEMETRY CABLE (#17). Feed the 3-PIN CONNECTOR (3P) end of the cable through the front of the HANDLEBAR ASSEMBLY (#15). The cable must be routed down the HANDLEBAR BRACKET TUBE (F) and back up the top of the MONOCOLUMN (#10). Feed the 3-PIN CONNECTOR through the DISPLAY CONSOLE MOUNTING BRACKET (D) ACCESS HOLE. 5. (Model 93S) Align the USER LEFT BULLHORN (#13) to the HANDLEBAR BRACKET TUBE (F). Using three MOUNTING SCREWS (#6), secure the USER LEFT BULLHORN to the HANDLEBAR BRACKET TUBE and the HANDLEBAR (#15). Tighten the SCREWS securely. Repeat the procedure for the USER RIGHT BULLHORN (#14). (Model 90S) Secure the HANDLEBAR ASSEMBLY (#15) to the HANDLEBAR BRACKET TUBE (F) using six MOUNTING SCREWS (#4). Tighten the SCREWS securely. 6. (Model 93S / 90S International) Locate the POLAR RECEIVER ASSEMBLY (#16). Plug the POLAR RECEIVER ASSEMBLY into the POLAR RECEIVER JACK (J). Place the POLAR RECEIVER in a vertical position, POLAR RECEIVER JACK facing downward, at the front of the HANDLEBAR BRACKET TUBE (F). Position the POLAR COVER (#19) over the center of the HANDLEBAR ASSEMBLY (#15) at the HANDLEBAR BRACKET TUBE. Making sure the POLAR COVER is oriented properly, slide the POLAR COVER over the HANDLEBAR ASSEMBLY covering the POLAR RECEIVER ASSEMBLY and the end of the HANDLEBAR BRACKET TUBE. The POLAR COVER should fully nest over the HANDLEBAR ASSEMBLY. Secure the POLAR COVER using two MOUNTING SCREWS (#8). (Model 90S) Position the POLAR COVER (#19) over the center of the HANDLEBAR ASSEMBLY (#15) at the HANDLEBAR BRACKET TUBE. Making sure the POLAR COVER is oriented properly, slide the POLAR COVER over the HANDLEBAR ASSEMBLY covering the end of the HANDLEBAR BRACKET TUBE. The POLAR COVER should fully nest over the HANDLEBAR ASSEMBLY. Secure the POLAR COVER using two MOUNTING SCREWS (#8). CAUTION: DO NOT OVER-TIGHTEN THE SCREWS (#8). MISE EN GARDE : NE SERREZ PAS EXCESSIVEMENT LES VIS (N. 8). 10 3P 15 F D 17 15 4 12 K 3 5 10 D 5 11 9 L 18 K 7. Locate one of the VERTICAL HANDRAILS (#12). Carefully insert the top of the VE...