Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * This product must be assembled on a flat, level surface to assure its proper function. DO NOT securely tighten any frame connections until the entire frame has been assembled, unless otherwise stated. Tools Required for Assembly * 3/4” wrench * 9/16” wrench * Ratchet with 3/4” and 9/16” sockets * Adjustable wrench * Tape measure _Bolt Length Ruler_ NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. I ////// /i I///////I BOLT LENGTH RULER: BOLT LENGTH PARTS LIST KEV PART# DESCRIPTION QIY KEY PART# DESCRIPTION QIY 1 6800208 UPRIGHT 1 20 6236701 1-3/4” SQ. END CAP 1 2 6800602 ADJ FOOT SUPPORT 1 21 6412001 SPRINGPIN ASSEMBLY 1 3 6800808 PULLEYHOUSING 1 22 3203301 VINYL CAP 2 4 6801008 TOPBOOM 1 23 6542402 3/16 X1-3/4 X 5-1/4” PLATE 2 5 6801102 LATBAR SUPPORT 1 24 6416601 3/4 X1-1/2” GLIDE 1 6 6759802 CARRIAGE 1 25 3102943 1/2 X 3-1/2” BOLT 1 7 6274402 LOW ROW BAR 1 26 3102502 1/2” WASHER 2 8 6725302 LATBAR 1 27 3102801 1/2” LOCK NUT 1 9 3116201 3-1/2” PULLEY 28 3102917 1/2X4” BOLT 1 10 3116101 4-1/2” PULLEY 1 29 3102807 3/8” LOW HEIGHT LOCK NUT 3 11 6802101 115-1/4” CABLE 1 30 3102501 3/8” WASHER 14 12 6671601 121-3/4” CABLE 1 31 3102802 3/8” LOCK NUT 9 13 6692601 3X2” END CAP 2 32 3102922 3/8 X 2-3/4” BOLT 6 14 3103102 IX 8” GRIP 4 33 6480301 3/8” FLANGE SPACER 8 15 6140701 1X1” GLIDE 8 34 3103801 5/16” SNAP HOOK 3 16 6405201 2” SQ. END CAP 2 35 3102933 3/8X2” BOLT 2 17 3116001 1-1/4” SQ. RUBBERBUMPER 1 36 3108102 1/4” QUICK LINK 1 18 6177001 2-1/2 X 5-1/2” NON-SKID STRIP 2 37 6075906 12 LINK CHAIN 1 19 3119301 2-1/2” ROUND END CAP 2 38 3102906 3/8X4” BOLT 4 • Remove four 7/16” CAPPLUGS from the UPPER&LOWER CROSS SUPPORTS on the 888 SMITH MACHINE as shown in FIGURE 1. • Slide two 1X 8” GRIPS (14) on the LOW ROW BAR (7) and two 1X8” GRIPS (14) ontheLATBAR (8) as shown in FIGURE 12. • Attach the LAT BAR (8) to the ball end of the upper CABLE (11) using one 5/16” SNAPHOOK (34) as shown in FIGURE 12. • Attach the LOW ROW BAR (7) to the ball end of the lower CABLE (12) using one 12-LINK CHAIN (37) and two 5/16” SNAP HOOKS (34) as shown in FIGURE 12. Thank you for purchasing the Parabody 887 LAT OPTION. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer service department at (800) 328-9714. 13 STEP 11: • Loopthe 121-3/4” CABLE (12) around one 3-1/2” PULLEY (9) as shown in FIGURE 11. • LOOSELY assemble the 3-1/2” PULLEY (9) to the 3/16 X1-3/4 X 5-1/4” PLATES (23) using one 3/8 X 2” BOLT (35), two 3/8” WASHERS (30), and one 3/8” LOCK NUT (31). See FIGURE 11. • SECURELY thread the end of the 121-3/4” CABLE (12) 3/4 of the way into into the threaded housing on the UPRIGHT and SECURELY tighten jam nut. • SECURELY tighten the two 3/8 X 2” BOLTS (35) of the 3/16X1-3/4 X 5-1/4” PLATES (23). 12 STEP 2: • NOTE: It may be necessary' to loosen the 1/2 X 3-1/4” BOLTS of the LOWER CROSS SUPPORT connecting the UPRIGHT FRAME before beginning STEP 2. • Attach four 3/4 X 1-1/2” GLIDES (24) to the inside of the tube on the UPRIGHT (1) as shown in FIGURE 2 using the following steps: • Thoroughly clean all surfaces where the 3/4 X1-1/2” GLIDES (24) are to be attached. • Remove the 3/4 X1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces. • SECURELY assemble one SPRING PIN ASSEMBLY (21) to the spring pin barrel on the UPRIGHT (1). See FIGURE 3. • LOOSELY assemble the PULLEYHOUSING (3) and the UPRIGHT (1) to the LOWER CROSS SUPPORT using two 3/8 X 4” BOLTS (38), four 3/8” WASHERS (30), and two 3/8” LOW HEIGHT LOCK NUTS (29). See FIGURE 2. • Insert one 2” SQ. END CAP (16) into the end of the PULLEY HOUSING (3) as shown in FIGURE 2. 1 1/2 ! 1/2 1 1/2 | 1/2 | 1/2 | 1/2 [ 0|1I2|3I4|5|6 I_I_1_I_I_I_I_I I 1 11_I_I_I_I_I_1_I_I_1_I_1_1_1 5 FIGURE 3 STEP 3: • Insert two 2-1/2” ROUND END CAPS (19) into the ends of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. • Insert one 1 -3/4” END CAP (20) into the end of the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. • Apply two 2-1/2 X 5-1/2” NON-SKID STRIPS (18) to the ADJ. FOOT SUPPORT (2) as shown in FIGURE 3. • Attach four 3/4 X 1-1/2” GLIDES (24) to the outside of the ADJ FOOT SUPPORT (2) and four GLIDES to the inside of the tube on the UPRIGHT (1) as shown in FIGURE 3 using the following steps: • Thoroughly clean all surfaces where the3/4Xl-l/2” GLIDES (24) are to be attached. • Remove the 3/4 X1-1/2” GLIDES (24) from the paper backing and firmly apply them to all shown surfaces. • Pull back on the SPRING PIN (21) and CAREFULLY insert the ADJ. FOOT SUPPORT (2) into the UPRIGHT (1) as shown in FIGURE 3. FIGURE 10 ^32)3/8X2-3/4” STEP 10: • Route the threaded end of the 121-3/4” CABLE (12) through the slot ofthe PULLEY HOUSING then SE...