Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Life Fitness is a registered trademarks of Brunswick Corporation. Any use of this trademark, without the express written consent of Life Fitness is forbidden. 8114701 Rev A- 1 (07/06) Life Fitness offers a full line of premier fitness equipment for the home. TOTAL- BODY ELLIPTICAL CROSS- TRAINERS | TREADMILLS | LIFECYCLE ® EXERCISE BIKES STAIRCLIMBERS | GYM SYSTEMS 5100N. RIVERROAD, SCHILLERPARK, ILLINOIS 60176 LIFEFITNESS.COM R R1/ R3 LIFECYCLE EXERCISE BIKES ASSEMBLYINSTRUCTIONS KK LL JJ Tools Required: Metric Wrench Set, Metric Allen Wrench Set, Phillips Screwdriver 1. 2. 3. Locate and install the two LEVELER FEET (A) to the bottom of the REAR STABILIZER (B). With the bends facing rearward, attach the REAR STABILIZER (B) to the BASE UNIT (C) using two 50 mm BUTTON HEAD SCREWS (1) from the top of the REAR STABILIZER BRACKET (D) and two 15 mm BUTTON HEAD SCREWS (2) from the front side of the REAR STABILIZER BRACKET. Tighten the SCREWS securely. Locate the HANDLEBAR ASSEMBLY (E) and the SEAT ASSEMBLY (F). With the handlebars facing upward and forward, align the mounting holes of the HANDLEBAR ASSEMBLY with those in the SEAT ASSEMBLY. Secure the HANDLEBAR ASSEMBLY to the SEAT ASSEMBLY using four 15 mm BUTTON HEAD SCREWS (2) and FLAT WASHERS (3). Tighten the SCREWS securely. Connect the CONNECTOR (G) leading from the HANDLEBAR ASSEMBLY (E) with the CONNECTOR (G) leading from the SEAT ASSEMBLY (F). Be sure the connectors fully lock. Locate the SEAT BOTTOM (H). Align the SEAT BOTTOM mounting holes with those in the LOWER SEAT SUPPORT TUBES (J). Secure the SEAT BOTTOM using four 55 mm PHILLIPS SCREWS (4) and LOCK WASHERS (5). Tighten the SCREWS securely. Align the guide rollers located on the underside of the SEAT ASSEMBLY (F) with the SEAT EXTRUSION (L). Carefully guide the SEAT ASSEMBLY onto the SEAT EXTRUSION. Slide the SEAT ASSEMBLY fully forward. Connect the WIRE (M) leading from the user left side of the SEAT ASSEMBLY to the JACK located at the left front of the SEAT EXTRUSION. Insert the WIRE (M) into the WIRE HARNESS (N) located next to the JACK. In the hole located on the user right side of the SEAT EXTRUSION (L), behind the SEAT ASSEMBLY (F), install one 40 mm BUTTON HEAD SCREW W/LOCKING COMPOUND (7), one 24 mm FLAT WASHER (8), one RUBBER BUMPER SLEEVE (9), one 1" RUBBER BUMPER (10) and one 18 mm FLAT WASHER (3) as shown. R3 Only: NOTE: NOTE: R3 Only: 4. NOTE: Locate the ACCESSORY TRAY (K). Secure the ACCESSORY TRAY to the HANDLEBAR ASSEMBLY using four 8 mm PHILLIPS SCREWS (6) as shown. Tighten the SCREWS securely. The WIRE (M), JACK and WIRE HARNESS (N) are located on the user left side of the unit. Items shown on the right for clarity. Mount the SEAT ADJUSTMENT LEVER (O) to the user right side of the SEAT ASSEMBLY (F) using two 12 mm PHILLIPS SCREWS W/LOCKING COMPOUND (11). Tighten the SCREWS securely. Be sure to mount the SEAT ADJUSTMENT LEVER (O) with the adjustment knob facing upward as shown. Locate the SEAT EXTRUSION ENDCAP (P). Secure the SEAT EXTRUSION ENDCAP to the SEAT EXTRUSION (Q) using two 12 mm PHILLIPS SCREWS (12). Secure the SEAT BACK PAD (Q) to the UPPER SEAT SUPPORT TUBES (R) using four 55 mm PHILLIPS SCREWS (4) and LOCK WASHERS (5). Tighten the SCREWS securely. Secure the SEAT BACK COVER (JJ) to the SEAT BACK PAD (Q) using four M8 x 1.0 PHILLIPS SCREWS (19). Tighten the SCREWS securely. A zip-tie has been included to keep the MONOCOLUMN COVER (T) from falling during assembly. Untape the WIRE TIE (V) attached to the front of the MONOCOLUMN (S). Carefully pull the CONSOLE WIRE (W) through the SIDE ACCESS HOLE (X) of the MONOCOLUMN. Feed the CONSOLE WIRE through the GROMMET (Y) as shown and insert the GROMMET into the SIDE ACCESS HOLE. Locate the MONOCOLUMN (S). Slide the MONOCOLUMN COVER (T) onto the MONOCOLUMN as shown. Slide the MONOCOLUMN COVER up to the FRONT HANDLEBAR POSTS (U). 1 D 2 A B C R1 & R3 Recumbent Bikes Hardware List 1. 6. 7. (R1 Only) Assembly Sequence Seat Assembly Rear Stabilizer 4. & 5. Monocolumn, Wiring, Cover & Console Pedals Water Bottle & Bracket 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 2. & 3. Item Qty Description R1 R3 1 2 3 4 5 6 7 ...
Dieses Handbuch ist für folgende Modelle:Kraftstationen - R3 (3.87 mb)