Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Sears Dateigröße: 1.07 mb Dateiname: L0709400.pdf Unterrichtssprache:

If you have additional questions, please call our toll-free HELPLINE at 1-800-736-6879, Upper Body Arm Accessory Tray Handrail Storage Latch LEFT SIDE Walking Belt Foot Rails Rear Rollel Adjustment Bolts Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is 831.297390. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Towel Rack Console Upper Body Arm Water Bottle Holder (Bottle not included) Handrail Key/Clip RIGHT SIDE Hood Circuit Breaker Front Wheel ncline Cushioned Walking Leg Platform 4 ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Refer to the _rawings below to identify the small parts used in assembly. Assembly requires the included allen wrenc h _ and your own phillips screwdriver , adjustable wrench _pen end w_'_rlch and scissors :_. Handrail Washer (16)-2 Extension Leg Screw (34)-2 1/2" Screw (13)-6 I7 Flange Nut (57)-2 _. Handrai! B°!tS5_ __ 31/2" Handrail Bolt (89)-2 D3/8" Washer (99)-2 1. With the help of a second person, carefully lay the treadmill on its right side as shown (refer to the drawing on page 4 to identify the right side). 34 Insert the Extension Legs (41) into the treadmill. Make sure that the Extension Legs are turned so the Base Pads (36) are on the indicated side. Attach each Extension Leg with an Extension Leg Screw (34). With the help of a second person, carefully raise the treadmill to the upright position so the Extension Legs (41) are resting flat on the floor. 41 Shipping Bracket Bolt Refer to the inset drawing. Remove the nut, bolt, and shipping bracket from the left Upright (14). Nut 2. Refer to HOW TO LOWER THE TREADMILL FOR USE on page 11. Follow the instructions treadmill. in step 2 to lower the 16 Position the Left Handrail (2) on the left Upright (14) as shown. Thread a Handrail Bolt (15) with a Handrail Washer (16) into the left Upright and the Left Handrail. Do not tighten the Handrail Bolt yet, Attach the lower end of the Left Handrail (2) to the Extension Leg (41) with a 3 1/2" Handrail Bolt (89), a 3/8" Washer (99), and a Flange Nut (57). Do not tighten the Handrail Bolt yet, 3.Withthehelpofasecondperson,holdtheConsoleBase (6)andtheRightHandrail(32)neartherightUpright(14). FeedallexcessWireHarness(26)downintotheright Upright;ifnecessary,bendtheWireHarnessasshown. RoutetheWireHarness(26)throughthebracketonthe RightHandrail(32)asshown.Insertthebracketintothe rightUpright(14). Referto theinsetdrawing.PushtheStrainReliefClip(88) ontotheWireHarness(26).Inserta 1/2"Screw(13)into theStrainReliefClipandintotheindicatedholeinthe RightHandrail(32).MakesurethatthereisnoslackWire HarnessbetweentheStrainReliefClipandtheConsole Base(6).TightentheScrewintotheConsoleBase. IMPORTANT: The Strain Relief Clip (88) must be attached as instructed, 4. Attach the Console Base (6) to the Left and Right Handrails (2, 32) with three 1/2" Screws (13). 5. Thread a Handrail Bolt (15) with a Handrail Washer (16) into the right Upright (14) and the Right Handrail (32). Do not tighten the Handrail Bolt yet, Attach the lower end of the Right Handrail (32) to the Extension Leg (41) with a 3 1/2" Handrail Bolt (89), a 3/8" Washer (99), and a Flange Nut (57). Tighten all parts used in this step and in step 2 6. Attach the Storage Latch (12) to the left Upright (14) with two 1/2" Screws (13). Be careful not to overtighten the Screws. Refer to the inset drawing. Remove the backing from the Adhesive Clip (74). Press the Adhesive Clip onto the base of the Uprights (14) in the indicated location. Press the Allen Wrench (73) into the Adhesive Clip. 13 12 74 73 7 Make sure that all parts are tightened before you use the treadmill To protect the floor or carpet, place a mat under the treadmill OPERATION AND ADJUSTMENT THE PERFORMANT LUBE TM WALKING BELT Your treadmill features a walking belt coated with PERFORMANT LUBE TM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear, HOW TO PLUG IN THE POWER CORD A, DANG ER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or service man if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product--if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden ...

Herunterladen

Geben Sie zwei Ziffern: