Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
15. If you feel faint, dizzy, or short of breath while exercising, stop immediately and begin cooling down. 16. When the AEROFLYER is not in use, always fold it to the storage position and unbuckle the nylon belt. 17. When folding the AEROFLYER for storage, hold the resistance dials to prevent your hands from being pinched. 18. The AEROFLYER is intended for home use only. Do not use the AEROFLYER in any commercial, rental, or institutional setting. IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the AEROFLYER. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. HealthRider assumes no responsibility for personal injury or property damage sustained by or through the use of this product. The decals shown below have been placed on the AEROFLYER. If one of the decals is missing, or if it is not legible, please call our Customer Service Department toll-free at 1-800-999-3756 to order a free replacement decal. Apply the decal in the location shown. WARNING . The safety belt may present a hazard to children. . Unbuckle safety belt when the AeroFlyer is not in use. . Never allow children to play on or around the AeroFlyer. . Fold up AeroFlyer when not in use. 3 BEFORE YOU BEGIN Thank you for selecting the innovative HealthRider. AEROFLYER. The AEROFLYER blends advanced engineering with contemporary styling to provide you with a no-impact, total body workout in the convenience and privacy of your own home. For your benefit, read this manual carefully before using the AEROFLYER. If you have questions after reading the manual, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is HRAW56071. The serial number can be found on a decal attached to the AEROFLYER (see the front cover of this manual for the location of the decal). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Handle Handgrip Resistance Dial Leg Link Arm Hip Pad Electronic Monitor Pedal Storage Hole Upright Lock Knob Frame Nylon Belt 4 ASSEMBLY Assembly requires two people. Place all parts of the AEROFLYER in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed. Read through all steps before beginning assembly. As you assemble the AEROFLYER, make sure that all parts are oriented as shown in the drawings. Tighten all parts as you assemble them, unless instructed to do otherwise. Refer to the drawings below to identify the small hardware used in assembly. Note: If a part is not found in the parts bag, check to see if it has been pre-attached. Assembly requires two adjustable wrenches , a hammer , and a phillips screwdriver 3/8" Nylon Locknut (43)N2 3/8" Flat Washer (39)N4 Plastic Spacer (41)N2 3/8O x 5 1/2O Screw (42)N2 3/8" x 4" Screw (44)N4 3/8O Lock Washer (58)N2 Bronze Bushing (16)N4 #8 x 3/4" Screw (23)N1 3/8" Axle Cap (40)N4 #8 x 1/2" Pedal Screw (21)N8 1/2O Spacer (61)N43/8O Spacer (60)N2 #8 x 1/2" Handle Screw (48)N4 1. Read all instructions at the top of this page before beginning assembly. Refer to the drawing at the right and identify the Left and Right Uprights (1, 2). Note the location of the stop rods. Turn the Crossbar (10) so the Rocker Arm (9) is at the top. Attach the Crossbar to the Left Upright (1) with two 3/8O x 4O Screws (44) and two 3/8O Flat Washers (39). Do not tighten the Screws yet. Attach the Crossbar to the Right Upright (2) in the same manner. Fig. 1 1 Stop Rods 44 39 10 9 2 5 6 3. Attach the Right Frame Section (6) to the Right Upright (2) with a 3/8O x 5 1/2O Screw (42), a Plastic Spacer (41), and a 3/8O Nylon Locknut (43). Do not tighten the Nylon Locknut yet. 4. Slide the long end of the Nylon Strap (59) onto the Right Frame Section (6) as shown. Slide the short end of the Nylon Strap (59) and the Hip Pad (28) onto the Left Frame Section (5). Slide the Left and Right Frame Sections (5, 6) together. Make sure that the indicated hole is accessibleNif necessary, slide the Hip Pad (28) to the side. Attach the Frame Sections with a #8 x 3/4O Screw (23). Do not tighten the Screw yet. Attach the Left Frame Section (5) to the Left Upright (1) with a 3/8O x 5 1/2O Screw (42), a Plastic Spacer (41), and a 3/8O Nylon Locknut (43). Tighten all parts used in steps 1, 3, and 4. Center the Hip Pad (28) on the Left and Right Frame Sections (5, 6). Fig. 3 6 2 42 41 43 7 9 3 40 16 60 40 61 Pin Pin 2. Refer to figure 2b. Slide a Finger Guard (54) onto the pins on the Left Pivot Bracket (7). Note: The Finger Guards may already be attached. Find the Left Link Arm (11), which is...