Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
Press the dark blue SET button(+) to increase stride length. Press the green RESET button(–) to reduce stride length. Press the yellow MODE button to exit setting mode. Setting Your Weight: Press the yellow MODE button until arrow on bottom of display points to “CAL.” Press the dark blue SET button once to enter setting mode. Display will shift to show weight in pounds. For example, “L 165” means weight is set to 165 lbs. Press the dark blue SET button(+) to increase weight setting. Press the green RESET button(–) to reduce weight setting. Press the yellow MODE button to exit setting mode. Setting the Clock: Press the yellow MODE button until the arrow on the bottom of the display points to the clock icon . Press the dark blue SET button to enter clock setting mode (clock readout will flash). Press the green RESET button to advance Hours. Press the dark blue SET button to advance Minutes. Press the aqua CLOCK button to shift between 12 and 24 hour mode. (“H” will show in display for 24 hour mode.) Press the yellow MODE button to exit clock setting mode, or wait a few seconds for pedometer to automatically exit clock setting mode. DISPLAY MODES Press the yellow MODE button to cycle through: • STEP: STEP mode shows your step count since last reset, up to 200,000 steps. • DIST: DISTANCE mode shows distance walked or jogged since last reset, in miles or kilometers. • CAL: CALORIE mode shows calories burned through step activity since last reset. • : ACTIVITY TIMER MODE shows total activity time in minutes and seconds then hours and minutes since last reset. The timer runs automatically whenever steps are being recorded. • : CLOCK mode shows time of day. • SCAN mode: Loops through each display mode, briefly showing step count, then distance, then calories. ACCUSPLITEAGLES E T TW15MGSTEP DIST CAL 1690SCAN MODE 627 IR E S E T MYCALORIE™ + – Dark Blue: SET Green: RESET Aqua: CLOCK (momentary) Cream: SCAN (toggle on/off) Yellow: MODE Current mode arrow indicator WEARING YOUR PEDOMETER While gently holding the belt clip open, slide the pedometer onto your belt or the top edge of your pants or skirt. It should fit snugly and level, above one knee. Note:The pedometer should be as vertical as possible. Walkers with larger stomachs may find it helpful to wear the pedometer farther back on the body, toward one hip. The cover must be closed for the pedometer to work.To avoid losing or dropping your pedometer, use the included leash and clip to fasten the pedometer securely to your clothing. Eat Right! Walk More! Live Well! The ACCUSPLIT Lifestyle 10 steps ACCUSPLIT, Inc. • 6120 Stoneridge Mall Rd., Suite 210 • Pleasanton, CA 94588 USA 800-965-2008 • 925-226-0888 • FAX 925-463-0147 • • support@ACCUSPLIT.com First, loop the pedometer clip Next, loop the metal clip, then clasp clothing Or, loop a belt or belt loop Or, loop a badge holder, then put into pocket (Badge holder not included) looping the leash around the pedometer belt clip. Next, clasp the waistband of your clothing with the attached metal clip. You can also use a safety pin to fasten the leash to your clothing, or loop the leash through your belt or belt loop. VIEWING YOUR RESULTS Once you put on your pedometer with the cover closed, it will automatically begin to record your steps, distance, calories burned, and activity time. Repeatedly press the yellow MODE button to cycle through the pedometer modes: STEPS > DISTANCE > CALORIES > ACTIVITY TIMER > TIME OF DAY > STEPS Press and hold the aqua colored CLOCK button to momentarily recall current time of day. NO-PROOF-OF-PURCHASE LIMITED WARRANTY See label inside the lid of your pedometer SCAN MODE In Scan mode, the unit cycles through each of the display modes (steps, distance, calories, clock, and activity time), showing each one for five seconds. Press the cream SCAN button to turn scanning on or off. The scan indicator (in the bottom left-hand corner of display) will turn on to show when you are in Scan mode. AUTO MOVEMENT SENSOR 1. To filter out random movements, the unit remains in standby mode until 5 continuous steps are registered. Only then are the 5 steps calculated in, and an Active indicator “^” appears on the upper left of display. 2. When regular walk/run movement stops, after 2 seconds the timer pauses and the unit switches to standby status (Active indicator “^” disappears). RESETTING YOUR PEDOMETER Most people prefer to reset their pedometers daily. Press and hold the green RESET button for at least two seconds to reset steps, distance, calories, and activity time measurements back to zero. REPLACING THE BATTERY When the display starts to dim or goes blank, it is time to replace the battery. Your pedometer uses one Type LR43 (L1142) 1.5 volt alkaline battery. To replace: 1. Insert a coin into the slot on the bottom of the case, and twist counterclockwise to loosen the case front. Lift case front away. 2. Using a pen or other thin object, push battery sideways out of its holder. Re...