Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Next, locate the Left Upright (31), which has an identification sticker. Orient the Left Upright so the sticker is on the inside as shown and the bracket is in the position shown. Attach the Left Upright (31) to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet. Note: There may be left and right stickers on the Upright Base. 48 Wheel Holes Sticker Bracket 40 39 31 1 6 7 2. Orient the Right Upright (36) so the square hole near the lower end is in the position shown. Attach the Right Upright to the Upright Base (48) with two Upright Bolts (40) and two Upright Star Washers (39). Do not tighten the Upright Bolts yet. Attach each Wheel (45) to the Upright Base (48) with a Wheel Bolt (89), two Wheel Spacers (44), and a Nut (47) as shown. Do not overtighten the Wheel Bolts; the Wheels should turn freely. 48 Square Hole 45 47 44 89 45 44 36 44 89 47 2 3. Cut the tie securing the Wire Harness (28) in a bundle. Do not remove the large colored tie on the end of the Wire Harness. Orient the Upright Base (48) so the Wheels (45) are at the bottom. Next, position the Upright Base and the Uprights (31, 36) around the frame assembly as shown. Have another person lift the front of the frame assembly and hold it. Insert the Wire Harness (28) into the square hole near the lower end of the Right Upright (36) and out of the top. Next, raise the Uprights (31, 36) so the Upright Base (48) is flat on the floor. Make sure that the end of the Wire Harness does not fall into the Right Upright; it may be helpful to hold the colored tie on the end of the Wire Harness. 28 Colored Tie 48 28 36 45 3 4. Open the included grease packet, and apply grease to both sides of each Frame Spacer (34). Hold one of the Frame Spacers (34) between the frame assembly and the Right Upright (36); make sure that the Frame Spacer is oriented as shown in the inset drawing. Insert a Frame Bolt (32) through a Frame Washer (33), the Right Upright, the Frame Spacer, and the bracket on the frame assembly. Be careful not to pinch the Wire Harness (28) in the Right Upright. Tighten a Nut (47) several turns onto the Frame Bolt, but do not fully tighten the Nut yet. Repeat this step on the left side. Note: There is not a wire harness on the left side. Remove the colored tie from the Wire Harness (28). Frame Assembly Bracket Frame Assembly Hole 34 32 33 4 47 28 36 Right Side Left Side 34 40 39 31 8 28 11 6. Hold the Console Base (26) near the Right Handrail (11). Attach the end of the ground wire on the Console Base to the indicated small hole in the Handrail with a Silver Ground Screw (27). Connect the Wire Harness (28) to wire harness on the Console Base (26). Make sure to connect the connectors properly (see the inset drawing). The connectors should slide together easily and snap into place. If the connectors do not slide together easily and snap into place, turn one connector and try again. IF THE CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. 27 26 Ground Wire 22 7. Set the console assembly on the Handrails (11, 18); insert the excess wiring down into the Right Handrail. Attach the console assembly with four 3/4” Screws (2), two Console Bolts (22), and two 1/4” Star Washers (21) as shown. Make sure that no wires are pinched. Start all four Screws and both Console Bolts before tightening any of them. 2 21 2 11 18 6 7 5. Identify the Right Handrail Endcap (91), which does not have a cutout in the bottom, and slide it onto the lower end of the Right Handrail (11). Make sure that the screw hole in the Right Handrail Endcap is at the bottom. Next, hold the Right Handrail near the Right Upright (36), and insert the Wire Harness (28) into the hole in the bottom of the Handrail and out of the indicated hole in the top. Then, remove the tie from the Wire Harness. Set the Right Handrail (11) on the Right Upright (36) while sliding the lower end of the Handrail onto the bracket on the Right Upright. Hand tighten two Handrail Bolts (20) with two Handrail Star Washers (19) into the Handrail and the Right Upright. Next, slide the Right Handrail Endcap (91) against the Right Upright, and tighten an Endcap Screw (95) into the Right Handrail Endcap. Then, tighten the two Handrail Bolts. Make sure that the Wire Harness (28) is not pinched. Attach the Left Handrail (18) and the Left Handrail Endcap (90) to the Left Upright (31) as described above. 36 31 95 95 91 Cutout 90 28 20 19 18 19 20 11 5 28 Console Assembly 21 22 8. Lower the Uprights (31, 36) until the Handrails (11, 18) are touching the floor. See the lower drawing. Position the Uprights (31, 36) so the treadmill Frame (74) is centered between them. Firmly tighten the four Upright Bolts (40) and the two Frame Bolts (32). Be careful not to overtighten the Frame Bolts. 9. Attach the end of the ground wire on the Wire Harness (28) to the indicated small hole in the Upright Base (48) with a Silver Ground Screw...