Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2 Features ......................................... 3 Notes ............................................ 3 Repair Policy .................................. 3 Specifications ................................. 3 Set-up ............................................ 4 Operation/Adjustments ................... 5 Maintenance .................................. 6 Legend ........................................... 6 Exploded View ............................... 7 WARRANTY POLICY FOR DSP SERIES LABEL DISPENSERS Brady Corporation warrants all parts on DSP series label dispensers against defects in design, materials and workmanship for a period of 180 days. Labor to replace defective parts will be performed at no charge for the first 90 days after date of purchase. Warranty does not cover transportation costs. Our sole obligation under this warranty is limited to repair, replacement or credit of the purchase price, at our option, for the machines listed above, which do not perform properly the function for which they were designed. Warranty repair is contingent upon our examination and determination that alleged defects have not been caused by misuse, abuse, improper installation or application, repair, alteration, accident or neglect in use, storage, transportation or handling. The above warranty and remedy constitutes Brady Corporation’s sole liability hereunder and are in lieu and exclusive of all other warranties and remedies expressed, implied, or statutory, including, but not limited to, those of merchantability and fitness for a particular purpose. 6-MOTOR6A-Motor/Main Plate screw(2ea) 2-REEL HOLDER ARM2A-Arm/Main Plate screw(1ea) 1-COVER1A-Cover/Base screw(4ea) 20-POWER INLET18-POWER SWITCH3-REEL HANGER BAR3A-Bar/Arm screw(1ea) 7-SQUARE LOCK ROD8-TAKEUP HUB 8A-Hub/Motor set screw(1ea) 10-GUIDE ROD10A-Rod/Main Plate screw(1ea) 11-BRUSH HOLDER 11A-Holder/Main Plate "T" screw(1ea) 11B-Holder/Brush set screw(2ea) 12-HOLD DOWN BRUSH13-STRIP PLATE 13A-Strip Plate/Main Plate screw(2ea) 13B-Teflon Tape15-PHOTOSENSOR BRACKET 15A-Bracket/Main Plate "T" screw(2ea) 15B-Bracket/Sensor screw(2ea) 14-PHOTOSENSOR 16-MAIN PLATE 5-REEL GUIDE(2ea) 21-DAISY CHAIN INLET 4-3" SPOOL(2ea) 17-BASE17A-Base/Main Plate screw-side(1ea) 17B-Base/Main Plate screw-bottom(2ea) 19-CIRCUIT BOARD 19A-Board/Base screw(4ea) 19B-Board/Base nut(4ea) 19C-Board/Base spacer(4ea) 22-TRANSFORMER 9-SHAFT COLLAR9A-"T" adjustment screw(1ea) NOTE: Drawing not to scale – for reference only. 2 7 ADJUSTMENTSSET-UP INSTRUCTIONS Place the label roll The roll should be so that it is held straight. labels snug. Thread the web under the guide and back under the strip plate. web in position with the metal lock counter-clockwise.) Reel Holder Arm Hold Down Brush Photosensor Strip Plate Guide Rod Lock Rod Take-up Hub Reel Hanger Bar Daisy-chain option: DSP-2 dispensers can be “daisy-chained” together to operate in series. When a label is removed from one of the machines, the next label will not feed until the labels are removed from all the machines. Example: If 3 machines are “daisy-chained” together, when a label is taken off the first machine, it will not feed; when a label is taken off the second machine, it will not feed. When the label is taken from the third machine, all machines will feed their respective labels. (DSP-2-CABLE needed to “daisy-chain” machines.) 4 Hold Down Brush: Using the upper thumbscrew tensioning. For best results, against the strip plate. However, if the labels are held too tightly, they will cause excessive drag Photosensor: The photosensor can be adjusted in any side of the machine and the thumbscrew underneath the photosensor bracket. Loosening the thumbscrew on the side of the machine allows This is used to set the overhang distance of the label thumbscrew underneath the photosensor bracket is used to swivel the front of the strip plate. When the label is being fed the in place. If there are 2 or more labels across, align the photosensor be removed. When these screws are locked in place, the machine Positioning of Photosensor Incorrect Sensor sees beyond label Sensor sees strip plate - Will not stop - Will not feed Correct Sensor sees front edge of label 5 MAINTENANCE FEATURES • Turn machine off when not in use. • Remove liner material diameter or if the motor • Do not operate machine without • Do not operate if inspection reveals • Keep strip plate, hold down brush LEGEND Model DSP-2 Item # Part # 1 1A 2 2A 3 3A 4 5 6 6A NV2000-12 NV1000-12-1 NV2000-07 NV1000-07-1 NV2000-08 NV1000-07-1 NV- SPOOL NV1000-22 NV1000-05 NV1000-05-1 7 8 8A 9 9A 10 10A 11 11A 11B NV2000-10 NV2000-09 NV1000-09-1 NV1000-18 NV1000-13-1 NV2000-06 NV1000-01-1 NV2000-03 NV1000-13-1 NV1000-03-1 12 13 13A 13B 14 15 15A 15B 16 17 NV2000-04 NV2000-02 NV1000-01-1 NV1000-02-1 NV1000-15 NV2000-13/21 NV1000-13-1 NV1000-15-1 NV2000-01 NV2000-11 17A 17B 18 19 19A 19B 19C 20 21 22 NV1000-11-1 NV1000-01-1 NV1000-16 NV1000-17 NV1000-17-1 NV1000-17-2 NV1000-17-3 NV1000-19 NV2000-2...